Maytag W10160251A manual End of Cycle Signal, Changing Cycles, Modifiers and Options

Page 22

Options

You can customize your cycles by selecting options.

Drum Light

On some models, select Drum Light to turn on the light inside the dryer drum. During a cycle, if Drum Light is selected, the drum light turns on and will remain on until DRUM LIGHT is pressed again, the door is opened and closed, or the door is left open for 5 minutes.

When the dryer is not running, the drum light will turn on when DRUM LIGHT is pressed or the dryer door is opened, and it will remain on until the dryer door has been open for

5 minutes, the dryer door is closed or DRUM LIGHT is pressed again. Press DRUM LIGHT at any time to turn the drum light ON or OFF.

Wrinkle Prevent Setting

The Wrinkle Prevent setting helps keep wrinkles from forming when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period.

Press the Wrinkle Prevent setting to get up to 120 minutes of heat-free, periodic tumbling at the end of a cycle.

Stop the WRINKLE PREVENT at any time by pressing Wrinkle Prevent setting or opening the dryer door.

For the Wrinkle Control Cycle, the Wrinkle Prevent setting is preset to ON. The other Sensor Dry Cycles will retain the Wrinkle Prevent setting. For example, if you select the Wrinkle Prevent setting in the Normal cycle, the Wrinkle Prevent setting will be on the next time you select the Normal cycle.

NOTE: If you do not select the Wrinkle Prevent setting, the dryer stops after cool down.

Damp Dry Chime

Select the Damp Dry Chime to alert you that your clothes are approximately 80% dry. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing.

The Damp Dry Chime is useful when drying bedsheets/linens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process.

NOTE: The Damp Dry Chime is available only with the Sensor Dry Cycles.

End of Cycle Signal

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press END OF CYCLE SIGNAL until the desired volume (High, Low or Off) is selected.

NOTE: When the Wrinkle Prevent setting is selected and the End of Cycle Signal is on, a tone sounds every 5 minutes until the clothes are removed, or the Wrinkle Prevent setting ends.

Changing Cycles, Modifiers and Options

You can change Sensor Dry and Timed Cycles, Modifiers and Options anytime before pressing Start.

Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1.Press PAUSE/CANCEL twice.

2.Select the desired cycle and options.

3.Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change an Option or Modifier anytime before the selected Option or Modifier begins.

1.Press PAUSE/CANCEL once.

2.Select the new Option and/or Modifiers.

3.Press START to continue the cycle.

NOTE: If you happen to press PAUSE/CANCEL twice, the program clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all of your loads on all Sensor Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your Sensor Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions or personal preference. There are 3 drying settings: 1 (factory preset dryness level), 2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying time).

1.The Dryness Level settings cannot be changed while the dryer is running.

22

Image 22
Contents Guide D’UTILISATION ET D’ENTRETIEN W10160251ATable of Contents Table DES MatièresDryer Safety Your safety and the safety of others are very importantImportant Safety Instructions Tools and Parts Installation InstructionsLocation Requirements Mobile home installations require Installation ClearancesMobile home Additional installation requirements Dryer DimensionsGas Type Electrical RequirementsGas Supply Requirements Natural GasBurner Input Requirements Gas Supply Line Gas supply connection requirementsDryer Gas Pipe Venting Requirements If using an existing vent systemIf this is a new vent system Vent material Plan Vent System Choose your exhaust installation typeRecommended exhaust installations ExhaustVent system chart Install Vent SystemAlternate installations for close clearances Special provisions for mobile home installationsMake Gas Connection Install Leveling LegsFor mobile home use Connect Vent Connect Inlet HoseLevel Dryer Remove the door assemblyReverse Door Swing Reinstall the door Reverse the strikeComplete Installation If the dryer will not start, check the followingDryer USE Starting Your DryerHow the Sensi-Care Drying System Works To use a Sensor Dry CycleTo make changes during a Sensor Dry Cycle To use a Timed CycleDrying and Cycle Tips Stopping, Pausing or RestartingStatus Lights Cycles Modifiers Options End of Cycle SignalChanging Cycles, Modifiers and Options To use the drying rack Rack Dry Setting Temp Time Wool SweatersDrying Rack Option Stuffed toys or pillowsDryer Care Vacation, Storage and Moving Care Changing the Drum LightTroubleshooting Dryer OperationStains on load or drum Cycle time too shortLint on load Loads are wrinkledU.S.A Assistance or ServiceAccessories CanadaMaytag Corporation Major Appliance Warranty ONE Year Limited WarrantySécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteQUE Faire Dans LE CAS D’UNE Odeur DE GAZ Importantes Instructions DE Sécurité Exigences d’emplacement Instructions D’INSTALLATIONOutillage et pièces Linstallation dans une maison mobile exige Dimensions de la sécheuseDégagements de séparation à respecter Type de gaz Spécifications électriquesAlimentation en gaz Gaz naturelAltitudes supérieures à 10 000 pi 3 048 m Caractéristiques d’alimentation du brûleurCanalisation d’arrivée de gaz de la sécheuse Épreuve sous pression de l’alimentation en gazConduit métallique rigide Exigences concernant lévacuationEn cas dutilisation du système dévacuation existant Conduit métallique flexibleBrides de serrage Planification du système d’évacuationÉvacuation Tableau des systèmes dévacuation Autres installations où le dégagement est réduitDéterminer litinéraire dacheminement du conduit Nombre de Type de Clapets de typeRaccordement au gaz Installation du système d’évacuationInstallation des pieds de nivellement Pour utilisation dans une maison mobileRaccordement du conduit d’évacuation Raccordement des tuyaux dalimentationInversion du sens douverture de la porte Réglage de laplomb de la sécheuseDépose de la porte Réinstallation de la porte Inversion de la gâcheFermer la porte vérifier l’engagement de la gâche Achever l’installation Si la sécheuse ne démarre pas, vérifier ce qui suitUtilisation DE LA Sécheuse Mise en marche de la sécheuseUtilisation dun programme minuté Utilisation dun programme de séchage par détectionFonctionnement du système de séchage Sensi-Care Utilisation d’un programme vapeurConseils pour le séchage et les programmes Arrêt, pause ou remise en marcheTémoins lumineux Programmes Modificateurs Signal de fin de programme Changement des programmes après avoir appuyé sur Start Changement des programmes, modificateurs et optionsModification des préréglages de niveau de séchage Séchage sur grille Réglage Temp Durée Chandails en laine Option de grille de séchageUtilisation de la grille de séchage Jouets rembourrés ou oreillersNettoyage du filtre à charpie Nettoyage de lemplacement de la sécheuseEntretien DE LA Sécheuse Nettoyage de l’intérieur de la sécheuseEntreposage ou un déménagement Retrait de la charpie accumuléeTuyaux darrivée deau Changement de l’ampoule d’éclairage du tambourFonctionnement de la sécheuse DépannageRésultats de la sécheuse Taches sur la charge ou sur le tambour Temps de programme trop courtCharpie sur la charge Charges avec faux plisAccessoires Assistance OU ServiceAu Canada Garantie DES Gros Appareils Ménagers Maytag Corporation W10160251A SP PN W10163137A Tous droits réservés