![](/images/new-backgrounds/1247168/247168199x1.webp)
Chapter | PowerLogic™ PM5300 series user guide |
|
|
5. Press Yes to confirm the reset or No to cancel and return to the previous screen.
Single resets
Single resets allow you to clear data only in a specific register or register type.
1.Navigate to Maint > Reset.
2.Move the cursor to point to Single Reset, then press Select.
3.Move the cursor to point to the parameter you want to reset, then press Reset. If there are additional options for the parameter, press Select, move the cursor to point to the option you want, then press Reset.
Single reset options
Parameter |
| Option | Description |
|
|
|
|
Energy | Accumulated |
| Clears all accumulated energy values (kWh, |
| kVARh, kVAh). | ||
|
|
| |
|
|
| Select which demand registers to clear |
Demand | Power, Current | (power demand, current demand or input | |
|
|
| metering demand). |
| Event Queue |
| Clears the alarm event queue register. |
|
|
|
|
| History Log |
| Clears the alarm history log. |
|
|
|
|
Alarms |
| All Alarm Counts, | Select “Counters”, then select which counter |
| Counters | (various alarm | to clear (choose all or individual alarm |
| counters) — see the | counters listed in the “Alarm counter options” | |
|
| ||
|
| next table | table below). |
|
|
|
|
|
| All Dig In Timers, | Select “Timers”, then select which status |
| Timers | Status Input S1, | input timer to clear (choose all or individual |
Status Inputs |
| Status Input S2 | status input timers). |
| All Dig In Counters, | Select “Timers”, then select which status | |
|
| ||
| Counters | Status Input S1, | input counter to clear (choose all or individual |
|
| Status Input S2 | status input counters). |
|
| All Dig Out Timers, |
|
| Timers | Digital Output D1, | Select “Timers”, then select which digital |
| Digital Output D2, | output timer to clear (choose all or individual | |
|
| Relay R1, | digital output timers). |
Digital Outputs |
| Relay R2 |
|
| All Dig Out Counters, |
| |
|
|
| |
|
| Digital Output D1, | Select “Timers”, then select which digital |
| Counters | Digital Output D2, | output counter to clear (choose all or |
|
| Relay R1, | individual digital output counters). |
|
| Relay R2 |
|
Active Load Timer |
|
| Clears and restarts the load operation timer. |
|
|
|
|
|
| Clears accumulated values in all tariff | |
|
| register. | |
|
|
|
4.Enter the reset password if prompted (default is “0000”), then press OK.
5.Press Yes to confirm the reset or No to cancel and return to the previous screen.
Alarm counter options
Alarm counter | Option | Description | |
|
|
| |
| Over Current, Ph |
| |
|
|
| |
Current | Under Current, Ph | Select which alarm counter register to reset from | |
Over Current, N | the current alarm condition counters. | ||
| |||
|
|
| |
| Over Current, Gnd |
| |
|
|
| |
| Over Voltage, |
| |
|
|
| |
| Under Voltage, |
| |
|
|
| |
| Over Voltage, | Select which alarm counter register to reset from | |
|
| ||
Voltage | Under Voltage, | ||
the voltage alarm condition counters. | |||
|
| ||
| Over Voltage Unbal |
| |
|
|
| |
| Over Voltage THD |
| |
|
|
| |
| Phase Loss |
| |
|
|
|
100 | © 2014 Schneider Electric All Rights Reserved |