Apollo IMY instruction manual Certifications and Compliances Safety

Page 42

20. CERTIFICATIONS AND COMPLIANCES:

SAFETY

IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment for measurement, control and laboratory use, Part 1.

IP65 Enclosure rating (Face only), IEC 529 Type 4 Enclosure rating (Face only), UL50

ELECTROMAGNETIC COMPATIBILITY

Immunity to EN 50082-2	EN 61000-4-2 Level 2; 4		Kv contact 1
Electrostatic discharge
Electromagnetic RF fields	EN 61000-4-3	Level 3; 8	Kv air
		Level 3; 10 V/m 2
Fast transients (burst)	EN 61000-4-4	80 MHz - 1 GHz
		Level 4; 2	Kv I/O
RF conducted interference	EN 61000-4-6	Level 3; 2	Kv power
		Level 3; 10 V/rms
		150 KHz - 80 MHz
Emissions to EN 50081-2	EN 55011	Enclosure class A
RF interference
Notes:		Power mains class A

1. Metal bezel of unit connected with ground lead from rear bezel screw to metal mounting panel.

2. Self-recoverable loss of performance during EMI disturbance at 10 V/m: Process input and/or analog output signal may vary during EMI disturbance. For operation without loss of performance:

Unit is mounted in a metal enclosure (Buckeye SM7013-0 or equivalent) I/O and power cables are routed in metal conduit connected to earth ground.

Refer to the EMC Installation Guidelines for additional information.

21. CONSTRUCTION: Die-cast metal front bezel that meets NEMA 4/IP65 requirements for wash-down and/or dusty environments when properly installed. Pollution Degree 2. Case body is black, high impact plastic (panel gasket and mounting clips included).

22. CONNECTION: Removable terminal blocks

23. WEIGHT: 1.2 lbs. (0.54 kg)

-40-

Image 42

Contents Apollo Intelligent Meter Series Introduction Table of Contents Page Safety Information Safety SummaryDefinition of Terms General Description Theory of OperationBlock Diagram Programming and Operating the IMY Programming the IMYDisplay Module #2 Program Temperature Display Offset and Slope Reset Latched Alarms Display Alarm ValuesEnter Alarm Values Reset PEAK/VALLEY Memory BufferTemperature Offset Value Enter Offset ValueModule #4 Program Digital Filter and Remote Input Program Digital FilteringProgram Function of E1-CON and Optional E2-CON Cont’d Module #5 Program INTEGRATOR/TOTALIZER Program Decimal Point Position for the INTEGRATOR/TOTALIZERProgram INTEGRATOR/TOTALIZER Time Base Module #6 Program ALARM/SETPOINT Alarm #2 Assignment to Input or INTEGRATOR/ Totalizer Program Value for Alarm #2Alarm #2 High or LOW Acting Print Request Function Baud RateUnit Address Number Full or Abbreviated TransmissionAnalog Output LO Display Value Module #8 Program RE-TRANSMITTED Analog OutputAnalog Output Source Analog Output HI Display ValueEnter Zero Reference Module #9 Service OperationsEnter Access Code Apply Precision ResistanceOperating the IMY Quick ProgrammingFactory Configuration SlopeProgramming Example Temperature Monitoring Example Offset and Slope Display Temperature INTEGRATOR/TOTALIZERPEAK/VALLEY INTEGRATOR/TOTALIZER Example Basic SET-UPINTEGRATOR/TOTALIZER SET-UP 125 x 827 Alarms Optional Alarm Timing DiagramsGeneral Description Communication FormatSending Commands to the IMY Command String ExamplesTiming Diagrams Receiving Data from the IMY Current Loop InstallationWiring Connections Serial Terminal DescriptionsConnecting to AN RLC Printer Serial Communications ExamplesProcess Controlling System RE-TRANSMITTED Analog Output Optional Analog Output Calibration To 20 mA CalibrationAppendix a Installation & Connections Installation EnvironmentSelect AC Power 115/230 VAC EMC Installation Guidelines Wiring Connections Power WiringAppendix B Specifications and Dimensions Open Thermistor Detection Display UlululTo 20 mA Certifications and Compliances Safety Appendix C Troubleshooting Guide Problem Possible Cause RemediesAppendix D Programmable Functions Decimal Point PositonAppendix D Programmable Functions Cont’d Appendix E Ordering Information E2-CONLimited Warranty IMY/IM-A 3/02 Drawing NO. LP0311