Apollo IMY instruction manual Appendix D Programmable Functions Cont’d

Page 45

APPENDIX “D” - PROGRAMMABLE FUNCTIONS (Cont’d)

“Pro 5” - PROGRAM INTEGRATOR/TOTALIZER

“dECPNt”	-	Enter decimal point for totalizer
“tbASE”	-	Enter time base
0	-	second
1	-	minute
2	-	hour
“SCLFAC”	-	Enter multiplying scale factor
“Lo-cut”	- Enter low-signal cut out
“Pro 6” - PROGRAM ALARMS
“trAc”	-	Enable alarm value tracking
“dISP”	-	Enable display alarm annunciators
“LAtC-1”	-	Enable alarm #1 latching
“ASN-1”	-	Enter alarm #1 trigger source ( temp. or integrator/ total)
“AL-1”	-	Enter alarm #1 value
“HYS-1”	-	Enter hysteresis value for alarm #1
“Act-1”	-	Enter alarm #1 action (high or low)
“LAtC-2”	-	Enable alarm #2 latching
“ASN-2”	-	Enter alarm #2 trigger source ( temp. or integrator/ total)
“AL-2”	-	Enter alarm #2 value
“HYS-2”	-	Enter hysteresis value for alarm #2
“Act-2”	- Enter alarm #2 action (high or low)

“Pro 7” - PROGRAM SERIAL COMMUNICATIONS

“bAud”	-	Enter baud rate
“AddrES”	-	Enter loop address number (0-99)
“Print”	-	Enter print function, or “P” command function through
	-	Serial Option
0	-	temp.
1	-	temp.,	peak/valley, and offset
2	-	temp. and alarms
3	-	temp, peak/valley, alarms, hysteresis, and offset
4	-	total
5	-	temp. and total
6	-	temp.,	total, peak/valley, and offset
7	-	total and alarms
8	-	temp.,	total and alarms
9	-	temp.,	total, peak/valley, alarms, hysteresis, and offset
“FULL”	-	Enable complete or abbreviated printing
“Pro 8” - PROGRAM RE-TRANSMITTED ANALOG OUTPUT
“ASIN”	-	Select source of analog output (input or total)
“AN-Lo”	-	Enter 4 mA or 0 VDC display value
“AN-HI”	-	Enter 20 mA or 10 VDC display value

“Pro 9” - SERVICE OPERATIONS (Protected by access codes)

“Code 39” - Serial hardware (loop-back) test “Code 48” - Basic input calibration

“Code 66” - Reset programming to factory configuration

-43-

Image 45

Contents Apollo Intelligent Meter Series Introduction Table of Contents Page Safety Information Safety SummaryDefinition of Terms Theory of Operation General DescriptionBlock Diagram Programming the IMY Programming and Operating the IMYDisplay Module #2 Program Temperature Display Offset and Slope Enter Alarm Values Display Alarm ValuesReset Latched Alarms Reset PEAK/VALLEY Memory BufferEnter Offset Value Temperature Offset ValueProgram Digital Filtering Module #4 Program Digital Filter and Remote InputProgram Function of E1-CON and Optional E2-CON Cont’d Module #5 Program INTEGRATOR/TOTALIZER Program Decimal Point Position for the INTEGRATOR/TOTALIZERProgram INTEGRATOR/TOTALIZER Time Base Module #6 Program ALARM/SETPOINT Alarm #2 Assignment to Input or INTEGRATOR/ Totalizer Program Value for Alarm #2Alarm #2 High or LOW Acting Unit Address Number Baud RatePrint Request Function Full or Abbreviated TransmissionAnalog Output Source Module #8 Program RE-TRANSMITTED Analog OutputAnalog Output LO Display Value Analog Output HI Display ValueEnter Access Code Module #9 Service OperationsEnter Zero Reference Apply Precision ResistanceQuick Programming Operating the IMYSlope Factory ConfigurationProgramming Example Temperature Monitoring Example Offset and Slope Display Temperature INTEGRATOR/TOTALIZERPEAK/VALLEY INTEGRATOR/TOTALIZER Example Basic SET-UPINTEGRATOR/TOTALIZER SET-UP 125 x 827 Alarm Timing Diagrams Alarms OptionalCommunication Format General DescriptionCommand String Examples Sending Commands to the IMYTiming Diagrams Wiring Connections Current Loop InstallationReceiving Data from the IMY Serial Terminal DescriptionsSerial Communications Examples Connecting to AN RLC PrinterProcess Controlling System RE-TRANSMITTED Analog Output Optional To 20 mA Calibration Analog Output CalibrationAppendix a Installation & Connections Installation EnvironmentSelect AC Power 115/230 VAC EMC Installation Guidelines Power Wiring Wiring ConnectionsOpen Thermistor Detection Display Ululul Appendix B Specifications and DimensionsTo 20 mA Certifications and Compliances Safety Problem Possible Cause Remedies Appendix C Troubleshooting GuideDecimal Point Positon Appendix D Programmable FunctionsAppendix D Programmable Functions Cont’d E2-CON Appendix E Ordering InformationLimited Warranty IMY/IM-A 3/02 Drawing NO. LP0311