Apollo IMY instruction manual Factory Configuration, Slope

Page 22

FACTORY CONFIGURATION

The following chart lists the programming of the unit when shipped from the factory. (In Program Module #9, Code 66 will restore the unit to these values.)

“Pro 1”	“tYPE”	-	“700”
	“SCALE”	-	“F”
	“dECPNt”	-	“0.0”
“Pro 2”	“SLOPE”	-	“1.0000”
	“OFFSEt”	-	“0.0 F”
“Pro 3”	“dSP AL”	-	“yES”
	“ENt AL”	-	“yES”
	“dSPHYS”	-	“yES”
	“ENtHYS”	-	“yES”
	“rSt AL”	-	“yES”
	“dSPbUF”	-	“yES”
	“rStbUF”	-	“yES”
	“SELdSP”	-	“yES”
	“rSttOt”	-	“yES”
	“dSPOFF”	-	“yES”
	“ENtOFF”	-	“yES”
“Pro 4”	“FILter”	-	“1”
	“E1-CON”	-	“4” (Display Hold)
	“E2-CON”	-	“4” (Display Hold)
“Pro 5”	“dECPNt”	-	“0”
	“tbASE”	-	“0”
	“SCLFAC”	-	“1.000”
	“Lo-cut”	-	“0.0 F”

“Pro 6”	“trAc”	-	“NO”
	“dISP”	-	“NO”
	“LAtC-1” - “NO”
	“ASN-1” - “INPUt”
	“AL-1”	-	“0.0 F”
	“HYS-1”	-	“0.1 F”
	“Act-1” - “HI”
	“LAtC-2” - “NO”
	“ASN -2” - “INPUt”
	“AL-2”	-	“0.0 F”
	“HYS-2”	-	“0.1 F”
	“Act-2” - “HI”
“Pro 7”	“bAud”	-	“1200”
	“AddrES”	-	“0”
	“Print”	-	“0”
	“FULL”	-	“yES”
“Pro 8”	“ASIN”	-	“INPUt”
	“AN-Lo”	-	“0.0 F”
	“AN-HI”	-	“100.0 F”

-20-

Image 22

Contents Apollo Intelligent Meter Series Introduction Table of Contents Page Safety Summary Safety InformationDefinition of Terms General Description Theory of OperationBlock Diagram Programming and Operating the IMY Programming the IMYDisplay Module #2 Program Temperature Display Offset and Slope Reset Latched Alarms Display Alarm ValuesEnter Alarm Values Reset PEAK/VALLEY Memory BufferTemperature Offset Value Enter Offset ValueModule #4 Program Digital Filter and Remote Input Program Digital FilteringProgram Function of E1-CON and Optional E2-CON Cont’d Program Decimal Point Position for the INTEGRATOR/TOTALIZER Module #5 Program INTEGRATOR/TOTALIZERProgram INTEGRATOR/TOTALIZER Time Base Module #6 Program ALARM/SETPOINT Program Value for Alarm #2 Alarm #2 Assignment to Input or INTEGRATOR/ TotalizerAlarm #2 High or LOW Acting Print Request Function Baud RateUnit Address Number Full or Abbreviated TransmissionAnalog Output LO Display Value Module #8 Program RE-TRANSMITTED Analog OutputAnalog Output Source Analog Output HI Display ValueEnter Zero Reference Module #9 Service OperationsEnter Access Code Apply Precision ResistanceOperating the IMY Quick ProgrammingFactory Configuration SlopeProgramming Example Temperature Monitoring Example INTEGRATOR/TOTALIZER Offset and Slope Display TemperaturePEAK/VALLEY Basic SET-UP INTEGRATOR/TOTALIZER ExampleINTEGRATOR/TOTALIZER SET-UP 125 x 827 Alarms Optional Alarm Timing DiagramsGeneral Description Communication FormatSending Commands to the IMY Command String ExamplesTiming Diagrams Receiving Data from the IMY Current Loop InstallationWiring Connections Serial Terminal DescriptionsConnecting to AN RLC Printer Serial Communications ExamplesProcess Controlling System RE-TRANSMITTED Analog Output Optional Analog Output Calibration To 20 mA CalibrationInstallation Environment Appendix a Installation & ConnectionsSelect AC Power 115/230 VAC EMC Installation Guidelines Wiring Connections Power WiringAppendix B Specifications and Dimensions Open Thermistor Detection Display UlululTo 20 mA Certifications and Compliances Safety Appendix C Troubleshooting Guide Problem Possible Cause RemediesAppendix D Programmable Functions Decimal Point PositonAppendix D Programmable Functions Cont’d Appendix E Ordering Information E2-CONLimited Warranty IMY/IM-A 3/02 Drawing NO. LP0311