Furuno FR-2115/2125 manual Console type mounting, How to dismount the PTU cover

Page 16

(2)Remove the cover by grasping the knob on the top of the cover.

Fixing hole (rear)

*Screw (M3x8, 5 pcs.)

Slide forward

Knob*

*

*

*

Screw (M4x8, 2 pcs.)

Fixing hole (front)

Figure 1-11 How to dismount the PTU cover

9.Fasten the display unit to the mounting location at rear fixing holes (2 points) with M10 bolts, nuts and flat washers, using the pipe box spanner (supplied)

10.Close the PTU board cover.

11.Push the monitor forward until you hear a click. 12.Refasten the bolts removed at step 3.

13.Fix the left and right arm covers.

Console type mounting

1.Make six holes of 15 mm diameter and a cable entrance hole through the deck referring to the outline drawing at end of this manual.

2.Open the front cover.

3.Fix the equipment by using M12 bolts, nuts and washers.

4.Hoist the console to the deck by using the eye bolts attached to the console. Remove the eye bolts and set the cosmetic caps (w/washers) to the eye bolt holes.

1-8

Image 16

Contents Marine Radar B . N o . I M E 3 4 6 4 0 M Safety Instructions Power Switch in AC Powered Display Unit Power SwitchTable of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No Qty RemarksSystem Configuration Scanner Unit Mounting considerationsBe sure to remove the guide pins Assembling the scanner unitFastening the scanner unit to the mounting platform Fastening the radiator to the radiator bracketScanner unit, front view Mounting procedure Display UnitBefore mounting the display unit Tabletop mountingStay Setting catch to hole in stay 11 How to dismount the PTU cover Console type mountingSeparating the control head Display unit modification procedureSeparate type control head kit Type OP03-151, No Control head modification procedure 13 Detaching the control headPlate Connection of display unit to control head15 How to attach KB fixing plate Attachment of hoodWiring Scanner unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 Fabricating signal cable S03-74 =EMI cores Outer cores RFC-13 thick Inner cores RFC-10 thinFabricating the AC power cable supplied DPYCY-3.5Fabricating the DC power cable CVV-S 8 x 2C, option CVV-S 82CCable fed from rear of display unit Default Leading in cables to the display unitCable fed from outside display unit Cables fed from bottom of display unit for console mountConnections M4X8 2 pcsConnectors on the INT Board Connectors on the INT BoardChanging AC Power Specification How to attach NH connectorTuning Initialization Accessing Menus for Initialization and AdjustmentAdjusting Video Signal Level Restoring default settingsHeading Alignment Picture appears Deviated counterclockwiseAdjusting Sweep Timing Suppressing Main BangConfirming Magnetron Heater Voltage Magnetron heater voltage ratingInitial Setting Menus Press Radar Menu 0 0 0Initial SETTING2 menu Initial SETTING1 menuInitial SETTING3 menu Initial SETTING4 menu OWN Ship Information menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8Gyro Converter Board 64P1106 DIP switch, jumper wire settings Connection of external power supplyDefault setting Setting method 1 by gyrocompass specifications Gyrocompass type FrequencySetting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5Setting the heading readout on the radar display SW1Installation of the ARP board ARP Board ARP-26ARP board adjustment ARP Board 18P9002BFinal check ARP Board ARP-26RP Board RP-26 Table top/console type10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no13 Display pedestal, front view Performance Monitor PM-30 Necessary parts PM-30 and OP03-150 Code noProcedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page