Furuno FR-2115/2125 manual Display pedestal, front view

Page 52

Control section

M-card base

Control section front panel

Pan Head

Screw M2.6X5

(2 pcs.)M-card case lid

Figure 4-13 Display pedestal, front view

5.Loosen six screws to remove the front panel on the display pedestal.

6.Set the RP Board (14P0298) in the top slot of the pcb card case.

7.Run the connector from the card case in front of the GYRO CONVERTER Board.

8.Plug the connector in J1 on the RP Board.

9.Fasten the ground wire from the connector at the location shown below.

RP connector

	INT Board	GYRO
	INT Board	CONVERTER
		CONVERTER
		Board

FRONT

Fasten ground wire from connector to this screw.

(TOP VIEW)

RP Board

ARP Board

SPU Board

J1

Route cable between ARP and SPU Boards.

FRONT VIEW

Figure 4-14 Display pedestal, top view

4-13

Image 52

Contents Marine Radar B . N o . I M E 3 4 6 4 0 M Safety Instructions Power Switch in AC Powered Display Unit Power SwitchTable of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No Qty RemarksSystem Configuration Scanner Unit Mounting considerationsBe sure to remove the guide pins Assembling the scanner unitFastening the scanner unit to the mounting platform Fastening the radiator to the radiator bracketScanner unit, front view Mounting procedure Display UnitBefore mounting the display unit Tabletop mountingStay Setting catch to hole in stay 11 How to dismount the PTU cover Console type mountingSeparating the control head Display unit modification procedureSeparate type control head kit Type OP03-151, No Control head modification procedure 13 Detaching the control headPlate Connection of display unit to control head15 How to attach KB fixing plate Attachment of hoodWiring Scanner unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 Fabricating signal cable S03-74 =EMI cores Outer cores RFC-13 thick Inner cores RFC-10 thinFabricating the AC power cable supplied DPYCY-3.5Fabricating the DC power cable CVV-S 8 x 2C, option CVV-S 82CCable fed from rear of display unit Default Leading in cables to the display unitCable fed from outside display unit Cables fed from bottom of display unit for console mountConnections M4X8 2 pcsConnectors on the INT Board Connectors on the INT BoardChanging AC Power Specification How to attach NH connectorTuning Initialization Accessing Menus for Initialization and AdjustmentAdjusting Video Signal Level Restoring default settingsHeading Alignment Picture appears Deviated counterclockwiseAdjusting Sweep Timing Suppressing Main BangConfirming Magnetron Heater Voltage Magnetron heater voltage ratingInitial Setting Menus Press Radar Menu 0 0 0Initial SETTING2 menu Initial SETTING1 menuInitial SETTING3 menu Initial SETTING4 menu OWN Ship Information menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8Gyro Converter Board 64P1106 DIP switch, jumper wire settings Connection of external power supplyDefault setting Setting method 1 by gyrocompass specifications Gyrocompass type FrequencySetting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5Setting the heading readout on the radar display SW1Installation of the ARP board ARP Board ARP-26ARP board adjustment ARP Board 18P9002BFinal check ARP Board ARP-26RP Board RP-26 Table top/console type10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no13 Display pedestal, front view Performance Monitor PM-30 Necessary parts PM-30 and OP03-150 Code noProcedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page