Furuno FR-2115/2125 manual RP Board RP-26, Table top/console type

Page 49

4.3 RP Board RP-26

The RP Board RP-26, which providesvideo plotter functions, consists of a circuit board and a card drive both of which are accommodated in the display unit of the FR-2105 series radar.

Table top/console type

Necessary Parts: RP-26-T-2E (008-485-520)

	Name	Type	Qty	Code no.

	RP board	14P0298	1	008-487-640

	Card case assy.	–	1	–

	Panhead screw B	M4x8 C2700W	4	000-881-445

	Panhead screw B	M3x8 C2700W	2	000-881-404

	Panhead screw A	M2.6x5 C2700W	2	000-800-973

	Teethed lock washer	M4 C5191W	1	000-864-506
	(Outside teeth)	M4 C5191W	1	000-864-506
	(Outside teeth)

	Cable assy.	HIF6-100D-A-A-52	1	000-137-553

1.Lift the monitor and fix it with the stay. Refer to Chapter 1 for instructions.

2.Remove the right arm cover from the control head.

3.Fasten the card case to the right arm cover as follows:

a)Fasten the ground wire with an M4x10 screw and washer (supplied) as shown below.

b)Fasten the arm cover to the card case with three M4x8 screws (supplied).

Card case

Figure 4-9 Fastening the card case to the right arm cover

4-10

Image 49

Contents Marine Radar B . N o . I M E 3 4 6 4 0 M Safety Instructions Power Switch Power Switch in AC Powered Display UnitTable of Contents Standard Supply Equipment ListsName Type Code No Qty Remarks Optional EquipmentSystem Configuration Mounting considerations Scanner UnitAssembling the scanner unit Be sure to remove the guide pinsFastening the radiator to the radiator bracket Fastening the scanner unit to the mounting platformScanner unit, front view Display Unit Mounting procedureBefore mounting the display unit Tabletop mountingStay Setting catch to hole in stay Console type mounting 11 How to dismount the PTU coverSeparating the control head Display unit modification procedureSeparate type control head kit Type OP03-151, No 13 Detaching the control head Control head modification procedureConnection of display unit to control head PlateAttachment of hood 15 How to attach KB fixing plateWiring Scanner unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 =EMI cores Outer cores RFC-13 thick Inner cores RFC-10 thin Fabricating signal cable S03-74DPYCY-3.5 Fabricating the AC power cable suppliedCVV-S 82C Fabricating the DC power cable CVV-S 8 x 2C, optionLeading in cables to the display unit Cable fed from rear of display unit DefaultCables fed from bottom of display unit for console mount Cable fed from outside display unitM4X8 2 pcs ConnectionsConnectors on the INT Board Connectors on the INT BoardHow to attach NH connector Changing AC Power SpecificationAccessing Menus for Initialization and Adjustment Tuning InitializationAdjusting Video Signal Level Restoring default settingsPicture appears Deviated counterclockwise Heading AlignmentSuppressing Main Bang Adjusting Sweep TimingMagnetron heater voltage rating Confirming Magnetron Heater VoltagePress Radar Menu 0 0 0 Initial Setting MenusInitial SETTING2 menu Initial SETTING1 menuInitial SETTING3 menu OWN Ship Information menu Initial SETTING4 menuGyro Converter GC-8 Installation and connection of the Gyro Converter BoardGyro Converter Board 64P1106 DIP switch, jumper wire settings Connection of external power supplyDefault setting Gyrocompass type Frequency Setting method 1 by gyrocompass specificationsJP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompassSW1 Setting the heading readout on the radar displayARP Board ARP-26 Installation of the ARP boardARP Board 18P9002B ARP board adjustmentARP Board ARP-26 Final checkTable top/console type RP Board RP-2610 Display pedestal Necessary parts RP-26-Z-2E Code no Separate type control head13 Display pedestal, front view Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30Procedure Alarm KitNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page