7即時提示
播放期間,在所需提示點上按下LOOP IN/REALTIME CUE鍵。
¶此點將會接著做為新提示點錄製下來。
7檢查提示點(提示點取樣器)
在設定好提示點後,持續按著CUE鍵。
¶只要一直按著CUE鍵,就可聽到在設定提示點上的聲音。
¶在提示點取樣期間,若將CUE鍵放開,將會從該設定提示點上執行返回 提示(back cue)操作。
¶播放MP3時,提示點取樣操作僅限在相同資料夾內。
7回到一提示點(返回提示)
1.在播放期間,按下CUE鍵。
¶雷射唱機將會回到指定的提示點。
2.按下PLAY/PAUSE鍵(6)。
¶播放將會立即從指定的提示點上開始。
¶當飛梭模式設定為[VINYL],且快速返回功能設定為ON時,則在提示 待命期間,藉由按放飛梭轉盤的盤面,也就能從該提示點開始播 放。
¶播放MP3時,提示點取樣操作僅限在相同資料夾內。只要該提示點一 直未被覆蓋,即使在資料夾搜尋後也仍能保存在記憶體中。
欲變更播放速度時
來回移動節拍調整滑桿(TEMPO)
¶節拍改變的程度一切都會顯示在顯示窗中。
¶即使在改變節拍時,音高(音調)仍可保持平穩(請參閱以下的“應用主 要節拍控制功能”乙節)。
7選擇TEMPO節拍調整的範圍
按下TEMPO ±10/WIDE鍵。
每次按下此鍵,TEMPO節拍調整滑桿的變動範圍會在±10 %與WIDE之間輪 流改變。當設定為[±10],每次會以0.05 %為單位調整;在[WIDE]下,針 對CD播放每次會以0.5 %為單位調整,針對MP3播放則會為0.1 %。
¶[WIDE]的變動範圍在CD播放期間為±100 %;在MP3播放期間則為±16 %。
¶當變動範圍設定為[WIDE],則TEMPO ±10/WIDE按鍵會亮起,且顯示窗 中會出現[WIDE]指示燈。
¶在初次將電源打開時,設定的預設值為±10 %。
¶在-100 %時,播放會停止。
應用主要節拍控制功能
播放期間,按下MASTER TEMPO鍵。
MASTER TEMPO鍵及[MT]指示燈亮起。速度(節拍)現在已可應用節拍調整滑 桿(TEMPO)來變更,不過音高(音調)則保持不變。
¶在做數位化處理時,音質可能會有所降低。
¶在初次將電源打開時,本項功能是預設為OFF。
DJ雷射唱機的操作
飛梭轉盤功能
1.滑音操作(Pitch bend):在播放期間轉動飛梭轉盤。
當飛梭模式設定為[VINYL],只須觸碰轉盤的斜面便可操作飛梭轉盤。 若是觸碰上方盤面,即可產生不同的功能。
¶
¶當轉盤停止轉動,播放即會恢復原先的速度。
2.刮片播放(Scratch play):在播放期間轉動飛梭轉盤。
請參閱「進階操作」中的“刮片播放(Scratch Play)”。
3.音框搜尋:暫停期間轉動飛梭轉盤。
當飛梭模式設定為CDJ,聲音暫停模式會啟用,且當設定為[VINYL],靜 音暫停模式即會執行;CD的聲音會以相對於飛梭轉盤轉動的速度來做播 放。
¶暫停的位置會以每1音框的單位改變。
¶飛梭轉盤轉一圈相等於CD播放1.8秒(135音框)。
4.旋轉播放(Spin play):播放或暫停期間轉動飛梭轉盤。
請參閱「進階操作」中的“旋轉播放(Spin Play)”。
5.高速搜尋:播放期間轉動飛梭轉盤,同時持續按住SEARCH鍵
要執行高速搜尋,按住SEARCH鍵(1、¡)並依所要搜尋方向轉動飛 梭轉盤;高速搜尋會按相對於飛梭轉盤轉動的程度執行。
¶搜尋會按飛梭轉盤轉動的方向執行,而與按下SEARCH鍵無關。
¶當轉盤轉動停止,播放即會恢復正常。
¶當放開SEARCH鍵,此模式即取消。
¶播放MP3時,向前快轉/向後快轉僅限於同一資料夾內執行。
6.高速音軌搜尋:轉動飛梭轉盤同時持續按住TRACK SEARCH鍵。
欲執行高速音軌搜尋,按住TRACK SEARCH鍵(4、¢)的同時,依所 需搜尋的方向轉動飛梭轉盤;高速搜尋會按相對於飛梭轉盤轉動的桯度 執行。
¶搜尋會按飛梭轉盤轉動的方向執行,而與按下的TRACK SEARCH鍵無 關。
¶當放開TRACK SEARCH鍵,此模式即取消。
¶播放MP3時,搜尋僅限於同一資料夾內執行。
7.高速資料夾搜尋:轉動飛梭轉盤同時持續按住FOLDER SEARCH鍵 (MP3播放期間)。
欲執行高速資料夾搜尋,按住FOLDER SEARCH鍵(、\)同時,依所需 搜尋的方向轉動飛梭轉盤;高速資料夾搜尋會按相對於飛梭轉盤轉動的 程度執行。
¶搜尋會按飛梭轉盤轉動的方向執行,而與按下的FOLDER SEARCH鍵 無關。
¶當放開FOLDER SEARCH鍵,此模式即取消。
備註:
在飛梭轉盤的盤面上裝有一內建開關;切勿在轉盤上置放任何物品或 施加重力。切勿將飲料置於盤面上,以免液體濺入機件內部而導致故 障。
53
<DRB1402> ChH