Korg owner manual About the KONTROL49 and the driver ports, SW1/2, USB Port a, USB Port B

Page 51

 

VECTOR-Y

 

Specify the transmission port for the Y-axis of the vector joystick.

 

SW1/2

 

Specify the transmission port for switch 1 and switch 2.

 

PEDAL

 

Specify the transmission port for a connected foot controller.

 

FOOT SW

 

Specify the transmission port for a connected damper pedal or pedal

 

switch.

 

KEYBOARD

 

Specify the transmission port for the keyboard.

 

MAIN ENC

 

Specify the transmission port for program change or bank select mes-

 

sages sent by the main encoder.

 

MESG A

 

Specify the transmission port for MIDI messages transmitted by hold-

 

ing down the [MESSAGE] key and pressing a pad [2]–[8], and for MIDI

 

Clock messages.

 

MESG B

 

Specify the transmission port for user MIDI messages specified for

 

each scene and transmitted by pressing pads [9]–[16].

3

Press the OCTAVE SHIFT/CURSOR [®] key to proceed to “USBPort”

 

(select the port).

Operation–Setting mode

 

A (USB Port A)

 

The MIDI messages assigned to the controller will be transmitted to the

 

computer application via port A. (See “About the KONTROL49 and

 

the driver ports” below)

 

B (USB Port B)

 

The MIDI messages assigned to the controller will be transmitted to the

 

computer application via port B. (See “About the KONTROL49 and the

 

driver ports” below)

5

Press the OCTAVE SHIFT/CURSOR [√] key to return to “Controller

 

Select,” and specify the transmission port for other controllers.

 

(☞Steps 2–4)

6

When you have finished making settings for each controller, press the

 

[ENTER] key. The settings will be updated, and you will return to Play

mode.

If you want to keep the new settings, you must save them in Scene mode. If you turn off the power or select a different scene without saving, your new settings will be lost. (☞p.55 “Scene mode–[16] WRITE”)

The port settings are saved independently for each scene.

About the KONTROL49 and the driver ports

The KONTROL49’s USB-MIDI connection communicates with the computer using 3 input ports and 2 output ports, as described below.

Setting mode

(Red) (Green)

4 Use the main encoder to select the transmission port.

The driver of the application on a computer

KONTROL49

MIDI IN device

 

(MIDI IN Port) MIDI IN

 

(Port A) PORT A

Keyboard/Pad/Encoder/

 

Slider/Bend/Wheel/

(Port B) PORT B

Vector joystick/

 

Switch1/Switch2/

MIDI OUT device

Pedal/Foot switch

 

(MIDI OUT B Port) MIDI OUT

 

(Dedicated Port) CTRL

Transmitting/receiving data

dumps in native mode

 

MIDI IN

MIDI OUT A

MIDI OUT B

45

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Page Precautions Parameters SymbolsIii Encoders and keysTable of Contents User Mesg 1-8 User message USB-MIDI Port USB-MIDI Port settingContents of the package Main features Parts and what they do HEX Lock key Message keyScene key Exit key Sub-displaysAbout the pad numbers About the trigger pad functionsTransmit Midi messages Select the different KONTROL49 modesMidi connectors Power switch Power supply connector Contrast adjustment knob Switch jack Pedal jackMidi & AC adapter connection Making connections and turning the power onStandby Scene mode Play modeSetting mode Message modeQuick Start Turning on the powerOperation-Quick Start Quick Assign Saving a sceneManaging scene sets on your computer Display Play modeUsing the controllers Encoders and slidersIf note data is assigned Encoder and slider-related settingsTrigger pad-related settings Trigger padsVector joystick-related settings When the vector joystick is operatedPitch Bend, Mod Wheel Switches 1 and 2 settings Switches 1Pedal Pedal jack/SWITCH jack Pitch Bend & Mod Wheel controller settingsPedal-related settings Main encoder settingsMain encoder Octave setting Keyboard-related settingsKeyboard About the Octave SHIFT/CURSOR keys, Enter key, and Exit key Setting modeScene parameter settings Global parameter settingsEncoder Encoder assignment NoAsgn No AssignCC#000-127 Control Change Assigning Nrpn or RPN Moving the cursor Using the main encoder to input textInputting a name Available charactersUsing the trigger pads to input text Using the encoders and sliders to input textQuick-assign for control changes PAD 1-8 PAD 1-8 assignment Slider Slider assignmentTgle Toggle NoAssignCtrlChg# Control Change Momt MomentaryConstant PAD 9-16 PAD 9-16 assignmentPitch Bend Pitch Bend assignment Assigning a single Midi message to the full range up/ downVelocity PitchBnd Pitch BendMastrBal Master Balance Touch AfterTouchDown Assigning separate Midi messages to the up/down rangesLast Polyphonic key pressure Ch Channel AftertouchMOD MOD Wheel assignment KBD KeyboardPAD Pad CChg#000-127 Control Change VECTOR-X Vector-X assignmentVECTOR-Y Vector-Y assignment Using the switches in one-parameter modeINC-DEC One-parameter mode SW1/SW2 Two-parameter modeProgChg Program Change Using the switches in two-parameter modeSoft Soft Pedal SW1 SW2Damper Sostenut SostenutoPedal Pedal assignment Assigning a control change Foot SW Foot SW assignmentChange Keyboard Keyboard setting Curve7 Velocity Curve Curve1 V-Curve3 Velocity CurveCurve4, V-Curve5 Velocity Curve 4 Curve6 Velocity CurveMain ENC Main Encoder assignment TempoChg Tempo ChangePChg&BS Program Change & Bank Select Message Message setting BankSel Bank SelectFree Mesg Free Message ProgChg Program Change message BankSel Bank Select message PAD USB-MIDI Port USB-MIDI Port settingUSB Port B About the KONTROL49 and the driver portsSW1/2 USB Port aAbout the KONTROL49’s Midi connectors Global Global settingBacklit LCD Backlit setting PadBlink PAD Illumination settingPdlCalib Pedal Calibration Encd Encoder Sldr SliderMain Panic Panic message Message modeSnap Snapshot message GM on GM On messageStop Stop message User Mesg 1-8 User message Start Start messageContinue Continue message TAP Tap tempo messageSelect Scene Scene modeScnCh#01-16 Scene Midi Channel Midi ChannelDump Any Ch AnyPreload Write Midi Control Change messages Available Midi messagesChannel messages System Realtime messagesRPN MSB/LSB Channel Mode messagesSystem exclusive messages Preset Scene NameAbout native Korg mode Midi implementationCan’t install the driver TroubleshootingOperation in native mode Power does not turn onKeyboard or pads do not transmit velocity Connected external device or software does not synchronizeMain specifications Aftertouch 27, 28, 29, 31 IndexNrpn RPN Page Important Notice to Consumers
Top Page Image Contents