Korg KONTROL49 owner manual Slider Slider assignment, PAD 1-8 PAD 1-8 assignment

Page 30

Operation–Setting mode

[2] SLIDER (Slider assignment)

In the Slider assignment page, you can assign MIDI messages to sliders and specify the MIDI channel on which the messages will be transmitted, etc. You can assign a control change (CC#), RPN, or NRPN message to each slider.

1

Hold down the [SETTING] key and press pad [2].

 

You will be in the Slider assignment page, and the [SETTING] key and

pad [2] will light. The main display indicates “Slider Select” (select the slider to assign). The messages you can assign to a slider and the assignment procedure are the same as for an encoder. For details, refer to “Encoder assignment” (☞p.20).

You can use the Quick Assign procedure for sliders as well. For details, refer to “Quick-assign for control changes” in “Encoder assignment.”

[3] PAD 1–8 (PAD 1–8 assignment)

PAD 1–8 assignment lets you assign MIDI messages to pads 1 through 8, and specify the channels on which these messages will be transmitted.

You can assign a note message or a control change (CC#) to each pad.

If you assign a control change, the message will be transmitted with a value of either 0 or 127.

Pad velocity settings are maintained separately for each scene. As the pad velocity type, you can choose either to transmit a velocity value that corresponds to the force with which you strike the pad, or to transmit a fixed value regardless of your striking force.

1

Hold down the [SETTING] key and press pad [3].

 

Now you can make pad [1]–[8] assignments. The [SETTING] key and

pads [1] through [8] will light/blink. The main display will indicate “PAD# 01” (select the pad that you want to assign).

Sub-displays 1 through 8 will show the MIDI transmit channel, MIDI message, and pad transmission setting for each pad.

 

MIDI channel MIDI message type Note number Pad operation type

 

or

 

Control change number

 

For example if you operate the fifth encoder or slider, PAD#5 will be

 

 

selected and the main display will indicate “PAD# 05”.

2

Use the main encoder or the pads to select the pad that you want to

 

assign. To make your selection using the pads, simply press the desired

pad.

The pad selected for assignment will blink.

 

If both SW1 and 2 are lit, you can also use these switches to select a pad

 

to assign.

 

In the following pages where you specify the MIDI message type and

 

 

note number or control change number, you can use the

 

correspondingly-numbered encoder or slider to select a parameter or

 

edit a value. It’s convenient to use the slider to make large changes in a

 

value, and use the encoder to make fine adjustments.

3

Press the OCTAVE SHIFT/CURSOR [®] key to proceed to “Message

 

Select” (select the MIDI message).

(Red) (Green)

24

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Precautions Encoders and keys SymbolsIii ParametersTable of Contents USB-MIDI Port USB-MIDI Port setting User Mesg 1-8 User messageContents of the package Main features Parts and what they do Sub-displays Message keyScene key Exit key HEX Lock keySelect the different KONTROL49 modes About the trigger pad functionsTransmit Midi messages About the pad numbersContrast adjustment knob Switch jack Pedal jack Midi connectors Power switch Power supply connectorMaking connections and turning the power on Midi & AC adapter connectionStandby Message mode Play modeSetting mode Scene modeTurning on the power Quick StartOperation-Quick Start Saving a scene Quick AssignManaging scene sets on your computer Encoders and sliders Play modeUsing the controllers DisplayTrigger pads Encoder and slider-related settingsTrigger pad-related settings If note data is assignedVector joystick-related settings When the vector joystick is operatedPitch Bend, Mod Wheel Pitch Bend & Mod Wheel controller settings Switches 1Pedal Pedal jack/SWITCH jack Switches 1 and 2 settingsPedal-related settings Main encoder settingsMain encoder Octave setting Keyboard-related settingsKeyboard Global parameter settings Setting modeScene parameter settings About the Octave SHIFT/CURSOR keys, Enter key, and Exit keyEncoder Encoder assignment NoAsgn No AssignCC#000-127 Control Change Assigning Nrpn or RPN Available characters Using the main encoder to input textInputting a name Moving the cursorUsing the trigger pads to input text Using the encoders and sliders to input textQuick-assign for control changes Slider Slider assignment PAD 1-8 PAD 1-8 assignmentMomt Momentary NoAssignCtrlChg# Control Change Tgle ToggleAssigning a single Midi message to the full range up/ down PAD 9-16 PAD 9-16 assignmentPitch Bend Pitch Bend assignment ConstantTouch AfterTouch PitchBnd Pitch BendMastrBal Master Balance VelocityAssigning separate Midi messages to the up/down ranges DownCh Channel Aftertouch Last Polyphonic key pressureMOD MOD Wheel assignment KBD KeyboardPAD Pad VECTOR-X Vector-X assignment CChg#000-127 Control ChangeSW1/SW2 Two-parameter mode Using the switches in one-parameter modeINC-DEC One-parameter mode VECTOR-Y Vector-Y assignmentUsing the switches in two-parameter mode ProgChg Program ChangeSostenut Sostenuto SW1 SW2Damper Soft Soft PedalPedal Pedal assignment Foot SW Foot SW assignment Assigning a control changeChange Keyboard Keyboard setting Curve6 Velocity Curve Curve1 V-Curve3 Velocity CurveCurve4, V-Curve5 Velocity Curve 4 Curve7 Velocity CurveMain ENC Main Encoder assignment TempoChg Tempo ChangePChg&BS Program Change & Bank Select Message Message setting BankSel Bank SelectFree Mesg Free Message ProgChg Program Change message BankSel Bank Select message USB-MIDI Port USB-MIDI Port setting PADUSB Port a About the KONTROL49 and the driver portsSW1/2 USB Port BGlobal Global setting About the KONTROL49’s Midi connectorsBacklit LCD Backlit setting PadBlink PAD Illumination settingPdlCalib Pedal Calibration Encd Encoder Sldr SliderMain Message mode Panic Panic messageSnap Snapshot message GM on GM On messageStop Stop message TAP Tap tempo message Start Start messageContinue Continue message User Mesg 1-8 User messageScene mode Select SceneAny Ch Any Midi ChannelDump ScnCh#01-16 Scene Midi ChannelPreload Write System Realtime messages Available Midi messagesChannel messages Midi Control Change messagesChannel Mode messages RPN MSB/LSBMidi implementation Preset Scene NameAbout native Korg mode System exclusive messagesPower does not turn on TroubleshootingOperation in native mode Can’t install the driverConnected external device or software does not synchronize Keyboard or pads do not transmit velocityMain specifications Index Aftertouch 27, 28, 29, 31Nrpn RPN Page Important Notice to Consumers
Top Page Image Contents