Korg KONTROL49 owner manual Dump, Any Ch Any, ScnCh#01-16 Scene Midi Channel

Page 59

[13] MIDI Channel

Here you can select the MIDI channel for the currently selected scene, and the global MIDI channel.

Normally, the controllers of each scene will transmit messages on the MIDI channel that you specify for each controller in Setting mode (the “Any” setting described below). However, you can use the settings in this page to specify a MIDI channel for the entire scene, so that messages from all controllers will be transmitted on this MIDI channel regardless of the settings of the individual controllers.

1

Hold down the [SCENE] key and press pad [13].

 

Now you can make MIDI channel settings, and the [SCENE] key and

pad [13] will light, and the [ENTER] key will blink.

The main display shows the current MIDI channel setting for the scene.

 

Operation–Scene mode

3

Use the OCTAVE SHIFT/CURSOR [√]/[®] keys to move to “Global

 

MIDI Channel.”

4

Use the main encoder or the pads to select the global MIDI channel.

 

The range is 1–16 (ch).

5

Press the [ENTER] key.

 

The settings will be saved, and you will return to Play mode.

If you decide to cancel, press the [EXIT] key to return to Play mode.

Never turn off the power while settings are being saved. Doing so may destroy internal data.

2

Use the main encoder or the pads to select the MIDI transmit channel.

 

(☞p.4 “About the trigger pad functions–Input numerical values”)

Any Ch (Any)

If you select “Any Ch,” messages will be transmitted on the MIDI channel specified for each controller.

ScnCh#01–16 (Scene MIDI Channel)

MIDI messages from all controllers will be transmitted on the MIDI channel you select here.

You can’t use the pads to select the “Any Ch” setting.

The scene MIDI channel is stored separately for each scene. If you want to keep the changes you’ve made, save them in Scene mode. If you turn off the power or select a different scene without saving, your changes will be discarded. For details, see “Scene mode–[16] WRITE” (☞p.55).

[14] DUMP

In the Dump page you can transfer data between the KONTROL49 and Editor Librarian software running on your computer. You can transfer both scene parameters and global data.

1

Hold down the [SCENE] key and press pad [14].

 

You will enter the Dump page, and the [SCENE] key and pad [14] will

light.

2

From the Editor Librarian software running on your computer,

 

transmit a MIDI Data Dump or a Dump Request to transfer data.

 

For details on how to transfer data to and from the Editor Librarian

 

software, refer to “Editor Librarian software manual” on the included

 

CD-ROM.

3

Press the [EXIT] key to return to Play mode.

Scene mode

53

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Page Precautions Parameters SymbolsIii Encoders and keysTable of Contents User Mesg 1-8 User message USB-MIDI Port USB-MIDI Port settingContents of the package Main features Parts and what they do HEX Lock key Message keyScene key Exit key Sub-displaysAbout the pad numbers About the trigger pad functionsTransmit Midi messages Select the different KONTROL49 modesMidi connectors Power switch Power supply connector Contrast adjustment knob Switch jack Pedal jackMidi & AC adapter connection Making connections and turning the power onStandby Scene mode Play modeSetting mode Message modeQuick Start Turning on the powerOperation-Quick Start Quick Assign Saving a sceneManaging scene sets on your computer Display Play modeUsing the controllers Encoders and slidersIf note data is assigned Encoder and slider-related settingsTrigger pad-related settings Trigger padsPitch Bend, Mod Wheel Vector joystick-related settingsWhen the vector joystick is operated Switches 1 and 2 settings Switches 1Pedal Pedal jack/SWITCH jack Pitch Bend & Mod Wheel controller settingsMain encoder Pedal-related settingsMain encoder settings Keyboard Octave settingKeyboard-related settings About the Octave SHIFT/CURSOR keys, Enter key, and Exit key Setting modeScene parameter settings Global parameter settingsCC#000-127 Control Change Encoder Encoder assignmentNoAsgn No Assign Assigning Nrpn or RPN Moving the cursor Using the main encoder to input textInputting a name Available charactersQuick-assign for control changes Using the trigger pads to input textUsing the encoders and sliders to input text PAD 1-8 PAD 1-8 assignment Slider Slider assignmentTgle Toggle NoAssignCtrlChg# Control Change Momt MomentaryConstant PAD 9-16 PAD 9-16 assignmentPitch Bend Pitch Bend assignment Assigning a single Midi message to the full range up/ downVelocity PitchBnd Pitch BendMastrBal Master Balance Touch AfterTouchDown Assigning separate Midi messages to the up/down rangesLast Polyphonic key pressure Ch Channel AftertouchPAD Pad MOD MOD Wheel assignmentKBD Keyboard CChg#000-127 Control Change VECTOR-X Vector-X assignmentVECTOR-Y Vector-Y assignment Using the switches in one-parameter modeINC-DEC One-parameter mode SW1/SW2 Two-parameter modeProgChg Program Change Using the switches in two-parameter modeSoft Soft Pedal SW1 SW2Damper Sostenut SostenutoPedal Pedal assignment Assigning a control change Foot SW Foot SW assignmentChange Keyboard Keyboard setting Curve7 Velocity Curve Curve1 V-Curve3 Velocity CurveCurve4, V-Curve5 Velocity Curve 4 Curve6 Velocity CurvePChg&BS Program Change & Bank Select Main ENC Main Encoder assignmentTempoChg Tempo Change Free Mesg Free Message Message Message settingBankSel Bank Select ProgChg Program Change message BankSel Bank Select message PAD USB-MIDI Port USB-MIDI Port settingUSB Port B About the KONTROL49 and the driver portsSW1/2 USB Port aAbout the KONTROL49’s Midi connectors Global Global settingPdlCalib Pedal Calibration Backlit LCD Backlit settingPadBlink PAD Illumination setting Main Encd EncoderSldr Slider Panic Panic message Message modeStop Stop message Snap Snapshot messageGM on GM On message User Mesg 1-8 User message Start Start messageContinue Continue message TAP Tap tempo messageSelect Scene Scene modeScnCh#01-16 Scene Midi Channel Midi ChannelDump Any Ch AnyPreload Write Midi Control Change messages Available Midi messagesChannel messages System Realtime messagesRPN MSB/LSB Channel Mode messagesSystem exclusive messages Preset Scene NameAbout native Korg mode Midi implementationCan’t install the driver TroubleshootingOperation in native mode Power does not turn onKeyboard or pads do not transmit velocity Connected external device or software does not synchronizeMain specifications Aftertouch 27, 28, 29, 31 IndexNrpn RPN Page Important Notice to Consumers
Top Page Image Contents