Schneider Electric 5.0A, 3.0A, 2.0A, and 6.0A manual Current Menus, Rev , 07/2012 Ammeter, 17-EN

Page 19

48049-136-05	Micrologic™ 2.0A, 3.0A, 5.0A, and 6.0A Electronic Trip Units
Rev. 01, 07/2012	Section 2—Ammeter

To access the next menu, press the menu button (A). To access the next screen in a menu, press the scroll button (B).

Current Menu

The current (default) menu displays:

A.Phase current (IA) in A phase

B.Phase current (IB) in B phase

C.Phase current (IC) in C phase

D.Ground-fault current (Ig) (Micrologic 6.0A trip units only)

E.Neutral current (In)

To display next current, press scroll button.

NOTE: Neutral current is only displayed with a

4-pole circuit breaker with the neutral protection set to half or full. Refer to bulletin 48041-082-03 for NC CT wiring guidelines.

Figure 16: Navigation Buttons

A B

33356	menu
061

Figure 17:	Current Menus
A–A-Phase Current (IA)			B–B-Phase Current (IB)
06133354	06134248	06133342	06134248
	A		A
100 %			100 %
40 %			40 %
C–C-Phase Current (IC)			D–Ground-Fault Current (Ig)
06133343	06134248	06133344	06134248
	A		A

ENGLISH

	100 %		100 %
	40 %		40 %
	E–Neutral Current (In)		Return to A-Phase Current
06133345	06134248	06133354	A	06134248
	A		A
	100 %		100 %
	40 %		40 %

© 1999–2012 Schneider Electric All Rights Reserved

17-EN

Image 19

Contents Conserver pour usage ultérieur Page Retain for future use Micrologic 2.0A, 3.0A, 5.0A, and 6.0A Electronic Trip UnitsDeath or serious injury Hazard Categories and Special SymbolsPlease Note FCC NoticeTable of Contents List of Registers Rating Plug Removal New Rating Plug InstallationCommunications Trip Unit SettingsGeneral Information IntroductionMicrologic 3.0A Trip Unit Micrologic 2.0A Trip Unit0A Trip Unit Micrologic 5.0A Trip Unit Micrologic 6.0A Trip Unit Zone-Selective Interlocking Trips and clears the fault. Circuit breaker 2 does not tripMicrologic Trip Unit Long-Time Delay Values Trip Unit SwitchesLong-Time Protection Short-Time Protection Micrologic Trip Unit Short-Time Delay ValuesInstantaneous Protection Micrologic Trip Unit Ground-Fault Pickup Values Indicator LightsGround-Fault Protection Overload Indicator LightControl Power Trip Unit TestingMicrologic Trip Unit Configuration Trip Indicator LightsFunction Specification External Power Supply15-EN Ammeter Measurements Accessing InformationAmmeter Display17-EN Current MenuCurrent Menus Rev , 07/2012 Ammeter18-EN Peak MenuSwitch settings menu displays Switch Settings Menu19-EN Set pickup levels Switch Setting AdjustmentOperation Examples21-EN Set time delaySet Time Delay Rev , 07/2012 OperationSet time delays Set Time Delays22-EN 23-EN Zone-Selective Interlocking ZSIZSI Combinations Units24-EN Wire circuit breakers for zone-selectiveCommunication Module values Interlocking25-EN Set communication module valuesScreen Trip Unit Settings CheckTrip Unit Settings Trip Unit Operation Verification27-EN Equipment Ground-Fault Trip Functions TestingTrip Unit Resetting Trip Unit Status CheckRequired Tools Trip Unit ReplacementPreparation Trip Unit Removal Trip Unit ReplacementBattery Installation Rating Plug Removal30-EN Trip Unit Installation31-EN Circuit Breaker Accessory CoverReplacement Close switch cover aTrip Unit Setup Circuit Breaker Reconnection Trip Unit Installation Check32-EN New Rating Plug Installation Adjustable Rating Plug ReplacementRating Plug Removal Circuit Breaker Disconnection Battery ReplacementCircuit Breaker Accessory Cover Removal Battery ReplacementRev , 07/2012 Battery Replacement Withstand Module Replacement35-EN Module Module Name Equation Address Range Appendix A-Register ListList of Registers Register List37-EN Rev , 07/2012 Appendix A-Register ListSchneider Electric