Cal Flame LTR50001038 manual Changing the burner orifices, Replace the main burner orifices

Page 32

30Gas Conversion (continued)

Appendix	Step 2: Changing the burner orifices
	Step 2: Changing the burner orifices
	1. Replace the main burner orifices
	a. Remove the grates, flame tamers, and drip tray
		from the grill. See figure below.

b.Remove the locking pins from the end of the burners.

The locking pins are accessible by removing the drip tray and tilting the grill back. They can be seen underneath the grill in the back. See figures below.

c.Remove all burners by carefully lifting them up and away from the valve orifice.

Burner

Locking Pin

You will need:

•6mm socket or nut driver

•Two to five 1.9mm orifices (depending on your grill

•Pipe compound suitable for natural gas

Orifice

d.Using a 6mm socket or nut driver, remove the orifice for the burner.

e.Apply a small amount of pipe compound to the orifice threads.

f.Screw in the orifice until it is finger tight.

g.Tighten the orifice with the 6mm wrench.

h.Repeat the above steps for the remaining burners.

i.Replace the burners, flame tamers, drip tray, and grates.

You do not need to replace the locking pins. They are used to keep the burners in place during shipping and are not necessary to operate your grill.

Barbecue Grills

www.calflamebbq.com

LTR50001038, Rev. C

Image 32

Contents LTR50001038, Rev. C 12/26/11 Read all instructions before you Operate your grill Safety Instructions Placement and LocationInstructions Set-UpStorage Maintenance and RepairPrecautions Regarding Children Built-in Construction Location of grill enclosureConstruction materials This sectionBuilt-in Dimensions Model Description Width Depth HeightBuilt-in Construction Model Description Width DepthEnclosure Ventilation Plumbing for Side Burners Electrical Supply RequirementsInstallation Installing the TransformerInstalling Grills in Barbecue Islands Installing the RotisserieGas Requirements and Connection Leak Testing ProcedureGas Connection Cylinder Specification LP GasTank Requirements LP Gas Hook UpConnection Natural GasRequirements Basic Grill Operation Using Your GrillYour Grill Using GrillYour Grill ControlsUsingYour Grill Lighting the BurnersElectronically Lighting the Burners Manually Lighting the BurnersHeat Distribution on the Cooking Grates Convection FanCooking with the Rotisserie Loading food on the rotisserie rodOptional Grill Accessories OptionalSear Zone Infrared Burner Pizza Brick TrayPlacement Using the Charcoal TrayRemoval and Clean-up Charcoal TrayPull-Out Cutting Board Deep Fryer Helper SetGriddle Tray Cleaning and Maintenance MaintenanceStainless Steel Care and Cleaning Cleaning Products and MaterialsCleaning the Interior of Your Grill Rust RemovalBurners Rust removal with Instant Rust OutSteam Cleaning Your Grill Covering Your GrillCooking Grates Drip PanRemove the burners Seasonal CleaningClean the burners Clean the grill interior Clean the componentsReplace the burners Replace the componentsSnap-in Light Lens Light Bulb ReplacementLight Lens with Screw Clip Troubleshooting AppendixProblem Yellow Flame Problem Plugged orificeProblem Misalignment of Igniter on Burner Problem FlashbackSwitching the regulator Converting from LP to NGBehind the grill With your grillChanging the burner orifices Replace the main burner orificesAppendix Mark the rating plateInstalling Sear Zone Burners Wiring Diagram Replacement Parts Ordering replacement parts Part Grill SizeLimited Warranty Extent of WarrantyWarranty Performance Warranty LimitationsLegal Remedies Customer ServiceDisclaimers Don’t forget to register your new product at Locating the product serial number