Cal Flame LTR50001038 manual Plumbing for Side Burners, Electrical Supply Requirements

Page 9

Plumbing for Side Burners

1.Assemble a 3/8” pipe nipple to the 3/8” pipe tee using Teflon tape or pipe sealant. Use only sealant that is approved for use on LP gas.

2.Install the pipe tee assembly to the grill intake pipe. Tighten assembly and align the branch opening of the tee with the hole of the cabinet.

3.Connect the flexible hose (male end) to the pipe tee.

4.Install the side burner into the island by simply setting it in place.

5.Connect the female end of the flexible hose to the side burner intake pipe.

6.Connect gas supply to the grill.

7.Check for gas leaks using soap water solution.

Items Included with Barbecue

 

1) "T" adapter, 3/8"

GAS LINE

2)2 hose fittings, 3/8”

3)Regulator with hose

"T" adapter, 3/8" Threaded

 

 

To grill, located

 

To side burner, located

underneath and

 

behind grill

 

underneath behind burner.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

From Grill

From Side Burner

 

3/8" Fittings

To Propane Tank

7

Built-in Construction

Electrical Supply Requirements

Your Cal Flame grill must be plugged into a permanent, grounded 110V outlet with a dedicated 15A GFCI breaker in accordance with local codes or the National Electrical Code, ANSI / NFPA 70, or the Canadian Electrical Code, CSA C22.1.

It is the owner’s responsibility to ensure that the electrical connection to this appliance is properly installed. We recommend a contractor or licensed electrician install a dedicated 110V electrical service for your grill.

Do not use an extension cord to supply power to your Cal Flame grill. Such use may result in fire, electrical shock or other personal injury.

Do not install a fuse in the neutral or ground circuit. A fuse in the neutral or ground circuit may result in an electrical shock hazard.

Do not ground this appliance to a gas supply pipe or hot water pipe.

Use copper wire only. The use of aluminum wire may result in unsatisfactory connections.

Install 120VAC, 15 Amp duplex outlet in an accessible location under the grill inside the base enclosure.

Locate the electrical supply box inside the built-in enclosure within reach of the power cord so the connection is accessible when the grill is completely installed in the enclosure.

Barbecue Grills

LTR50001038, Rev. C

www.calflamebbq.com

Page 8 Page 10
Image 9
Page 8 Page 10
Contents LTR50001038, Rev. C 12/26/11 Read all instructions before you Operate your grill Placement and Location Safety InstructionsInstructions Set-UpMaintenance and Repair Precautions Regarding ChildrenStorage Location of grill enclosure Built-in ConstructionConstruction materials This sectionModel Description Width Depth Height Built-in DimensionsModel Description Width Depth Built-in ConstructionEnclosure Ventilation Electrical Supply Requirements Plumbing for Side BurnersInstalling the Transformer InstallationInstalling the Rotisserie Installing Grills in Barbecue IslandsLeak Testing Procedure Gas ConnectionGas Requirements and Connection LP Gas Cylinder SpecificationTank Requirements LP Gas Hook UpNatural Gas RequirementsConnection Using Your Grill Your GrillBasic Grill Operation Grill Controls Using GrillYourLighting the Burners UsingYour GrillElectronically Lighting the Burners Manually Lighting the BurnersConvection Fan Heat Distribution on the Cooking GratesLoading food on the rotisserie rod Cooking with the RotisserieOptional Optional Grill AccessoriesSear Zone Infrared Burner Pizza Brick TrayUsing the Charcoal Tray PlacementRemoval and Clean-up Charcoal TrayDeep Fryer Helper Set Griddle TrayPull-Out Cutting Board Maintenance Cleaning and MaintenanceStainless Steel Care and Cleaning Cleaning Products and MaterialsRust Removal Cleaning the Interior of Your GrillBurners Rust removal with Instant Rust OutCovering Your Grill Steam Cleaning Your GrillCooking Grates Drip PanSeasonal Cleaning Clean the burnersRemove the burners Clean the components Clean the grill interiorReplace the burners Replace the componentsLight Bulb Replacement Light Lens with Screw ClipSnap-in Light Lens Appendix TroubleshootingProblem Plugged orifice Problem Yellow FlameProblem Misalignment of Igniter on Burner Problem FlashbackConverting from LP to NG Switching the regulatorBehind the grill With your grillReplace the main burner orifices Changing the burner orificesMark the rating plate AppendixInstalling Sear Zone Burners Wiring Diagram Replacement Parts Part Grill Size Ordering replacement partsExtent of Warranty Limited WarrantyWarranty Performance Warranty LimitationsCustomer Service DisclaimersLegal Remedies Locating the product serial number Don’t forget to register your new product at
Top Page Image Contents