Cal Flame LTR50001038 manual Appendix, Mark the rating plate

Page 33

Gas Conversion (continued)

2. Replace the infrared burner orifices

3. Replace the side burner orifices

31

You will need:

•Either a 13mm or 10mm open end wrench

•One #50 orifice (for single infrared burner)

OR

•Two #54 orifices (for dual infrared burners)

OR

•One #52 orifice (for single infrared burner)

•Pipe compound suitable for natural gas

a.Unscrew the back cover from the grill and lift it up and under the grill hood.

b.Using a wrench, remove the orifice for the infrared burner.

You will need:

•7mm wrench, socket, or nut driver

•One or two 1.75mm orifices (depending on your side burner)

•Pipe compound suitable for natural gas

a.Remove the grate, burner cap and burner diffuser from the side burner.

b.Using a 7mm wrench, remove the orifice for the burner.

c.Apply a small amount of pipe compound to the orifice threads.

d.Screw in the orifice until it is finger tight.

e.Tighten the orifice with the 7mm wrench.

f.If you have dual side burners, repeat the previous steps for the second burner.

Appendix

4. Mark the rating plate

After conversion has been completed, mark the rating plate as NG with an indelible marker.

c.Apply pipe compound to the fitting threads where you will place the new orifice.

d.Screw on the correct orifice for your grill until it is finger tight.

e.Tighten the orifice with the wrench.

f.If you have dual infrared burners, repeat the previous steps for the second burner.

g.Replace the back cover.

Barbecue Grills

LTR50001038, Rev. C

www.calflamebbq.com

Image 33

Contents LTR50001038, Rev. C 12/26/11 Read all instructions before you Operate your grill Placement and Location Safety InstructionsInstructions Set-UpMaintenance and Repair Precautions Regarding ChildrenStorage Location of grill enclosure Built-in ConstructionConstruction materials This sectionModel Description Width Depth Height Built-in DimensionsModel Description Width Depth Built-in ConstructionEnclosure Ventilation Electrical Supply Requirements Plumbing for Side BurnersInstalling the Transformer InstallationInstalling the Rotisserie Installing Grills in Barbecue IslandsLeak Testing Procedure Gas ConnectionGas Requirements and Connection LP Gas Cylinder SpecificationTank Requirements LP Gas Hook UpNatural Gas RequirementsConnection Using Your Grill Your GrillBasic Grill Operation Grill Controls Using GrillYourLighting the Burners UsingYour GrillElectronically Lighting the Burners Manually Lighting the BurnersConvection Fan Heat Distribution on the Cooking GratesLoading food on the rotisserie rod Cooking with the RotisserieOptional Optional Grill AccessoriesSear Zone Infrared Burner Pizza Brick TrayUsing the Charcoal Tray PlacementRemoval and Clean-up Charcoal TrayDeep Fryer Helper Set Griddle TrayPull-Out Cutting Board Maintenance Cleaning and MaintenanceStainless Steel Care and Cleaning Cleaning Products and MaterialsRust Removal Cleaning the Interior of Your GrillBurners Rust removal with Instant Rust OutCovering Your Grill Steam Cleaning Your GrillCooking Grates Drip PanSeasonal Cleaning Clean the burnersRemove the burners Clean the components Clean the grill interiorReplace the burners Replace the componentsLight Bulb Replacement Light Lens with Screw ClipSnap-in Light Lens Appendix TroubleshootingProblem Plugged orifice Problem Yellow FlameProblem Misalignment of Igniter on Burner Problem FlashbackConverting from LP to NG Switching the regulatorBehind the grill With your grillReplace the main burner orifices Changing the burner orificesMark the rating plate AppendixInstalling Sear Zone Burners Wiring Diagram Replacement Parts Part Grill Size Ordering replacement partsExtent of Warranty Limited WarrantyWarranty Performance Warranty LimitationsCustomer Service DisclaimersLegal Remedies Locating the product serial number Don’t forget to register your new product at