DCS BGB" Series manual Burner Adjustment, Grill Burner AIR Adjustment, Grill Burner Flame Height

Page 19

INSTALLATION

BURNER ADJUSTMENT

GRILL BURNER AIR ADJUSTMENT:

Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply or a conversion from one gas to another may make it necessary to adjust the burners. The flames of the burners (except the rotisserie burner) should be visually checked and compared to that of the drawing in Fig.18. Flames should be blue and stable with no yellow tips (LP units may have some yellow tipping), excessive noise or lifting. If any of these conditions exist, check if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc. Proceed with air shutter adjustment. The amount of air which enters a burner is governed by a metal cup at the inlet of the burner called an air shutter. It is locked in place by a screw which must be loosened prior to lighting the burner for adjustment.

GRILL BURNER FLAME HEIGHT:

Before beginning, ensure the grill is OFF and cool. To access the grill burner air shutters, first remove the grates and radiants from the fire- box, then remove the grill burner using instructions shown on page 29, Fig. 46. With a screw driver, loosen the lock screw on the face of the air shutter slightly so that the air shutter can be adjusted.

To Adjust:

1.Be careful as the burner may be very hot.

2.If the flame is yellow, indicating insufficient air, turn the air shutter counterclockwise to allow more air to the burner.

 

1-1/2"

 

3/8"

 

E

 

S

LO

C

N

 

E

 

P

 

O

FIG. 18 Burner Flame

Height

3.If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air shutter clockwise.

Reinstall the U-burner, ensuring the burner is level. Light the burner and check the flame. If all is okay, remove the burner (CAUTION - burner may be hot, allow time to cool) and tighten the air shutter screw. If not repeat the above procedure to readjust the air shutter.

LOW FLAME SETTING ADJUSTMENT:

The valves on the grill feature an adjustable low setting. Due to fluctuations in gas pressure, heating value or gas conversion, you may feel it necessary to increase or decrease gas flow in the low position. We do not recommend adjusting the infrared rotisserie burner.

To Adjust:

1.Light the burner.

2.Turn the control knob to the lowest setting (all the way counter-clockwise).

3.Remove the knob.

4.While holding the valve shaft with pliers, insert a thin, flat tipped screwdriver into the shaft and while viewing the burner adjust to a minimum stable flame (Fig. 19).

FIG. 19 Low Setting Adjustment

SIDE BURNER FLAME HEIGHT:

The correct height of the flame mainly depends on the size of the bottom of the cooking utensil, the material of the cooking utensil, the amount and type of food and the amount of liquid in the utensil. Following are some basic rules for selecting flame height.

For safety reasons the flame must never extend beyond the bottom of the cooking utensil. Never allow flames to curl up the side of the pan (see Fig. 20).

Proper Flame Height

Fig. 20

Utensils which conduct heat slowly (such as glass-ceramic) should be used with medium to low flames. If you are cooking with a large amount of liquid, a slightly larger flame can be used.

WARNING: IMPORTANT!

Before lighting, inspect the gas supply piping or hose prior to turning the gas "on". If there is evidence of cuts, wear, or abrasion, it must be replaced prior to use.

17

Image 19
Contents Professional 36/48 BGB Grill Page Please Retain this Manual for Future Reference Message to OUR CustomersTable of Contents Important Safety Notice Safety Practices & PrecautionsPreferred AIR Flow Grill PlacementSafety Practices & Precautions Grill Models Locating GRILL/BUILT-IN Clearances InstallationLocation Clearances to Non-Combustible Construction Clearances to Non-Combustible ConstructionGeneral Clearances to Combustible ConstructionInsulated Jacket BUILT-IN Construction Details Access Drawers Cutout dimensions GAS HOOK-UP LP Gas LP Tank Requirements18 max LP Tank Restraint for BUILT-IN InstallationStep Before Testing Leak TestingTo Test Grill Burner Flame Height Burner AdjustmentGrill Burner AIR Adjustment LOW Flame Setting AdjustmentRadiant Asssembly Installation Radiant AssemblyThese Instructions Installer ChecklistLighting Instructions Using the GrillTo Light the Grill Burner Burner Off GrillingDIRECT/INDIRECT Cooking Notes BurnerDUAL-SIDED Grates Grilling HintsShaped Grate Radius Grate To Light the Smoker Burner Using the Smoker SystemWood Chips ROD Light Using the RotisserieMeat Preparation PreparationRecommended Working AreaManual Lighting To Light the Rotisserie Burner Before CookingCooking on Rotisserie Care and Maintenance Stainless Steel To Remove the U-BURNERS for CleaningGrill Burner Cleaning Orifice CleaningSmoker Burner Side Burners BGB48 BQR ModelLOW Heat with Knob in HI/SEAR Position TroubleshootingBefore Calling for Service Grill WON’T Light When the Ignition Button is PushedHOW to Obtain Service ServiceThis Warranty does not Cover WarrantyLimited Warranty HOW Long does this Limited Warranty LAST?Commercial USE HOW to GET ServiceNo Other Warranties LE Gril DE Série Professionnelle BGB 36/48 PO Veuillez Conserver CE Manuel À Titre DE Référence Lintention DE NOS ClientsTable DES Matières Autocollant Mesures DE Sécurité ET DE PrécautionDe ventilation Flux Dévent DE Sortie Emplacement DU GrilRemarque Modèles DE Gril Emplacement Emplacement DU Gril ET DES DégagementsEspaces de dégagement pour une construction non combustible Enveloppe Isolée GénéralitésDisposition standard pour une enceinte non combustible Détails Dune Construction IntégréeModèle Pour Connecter LES Raccords Fournis Avec LE Gril Branchement DU GAZExigences Concernant LE GAZ Branchement DU GAZ NaturelExigences Concernant LA Bouteille DE Propane Mise EN GardeRemarque Placez le dispositif de retenue de bouteille dans lîlot Fig Avant la vérification Test DE Détection DES FuitesPour tester Réglages Pour Niveau BAS Réglages DES BrûleursRéglage Dair DU Brûleur DU Gril Hauteur DES Flammes DU Brûleur DU GrilInstallation DE Lensemble DU Radiant Installation DE Lensemble DU RadiantListe DE Contrôle DE Linstallateur Allumage du gril à lallumette Utilisation DU GrilInstructions Dallumage Pour Allumer LE Brûleur DU GrilGril Instructions DALLUMAGE/CUISSON SUR GrilAllumage des brûleurs latéraux avec une allumette Brûleurs latérauxConseils AU Sujet DU Gril Cuisson SUR GrilGrille EN Forme DE « W » Grille Arondie Grilles Double FacePour Allumer LE Brûleur À Fumoir Utilisation DU Système À FumoirCopeaux DE Bois Utilisation DE LA Rôtissoire Préparation RecommandéAllumage Manuel Pour Allumer LE Brûleur DE Rôtisserie Avant DE Faire CuireCuisson SUR LA Rôtissoire Entretien ET Nettoyage Déposer DES Brûleurs EN U Pour LE Nettoyage Acier InoxydableÉlectrodes Brûleur DU GrilBrûleur À Fumoir Brûleurs Latéraux BGB48 BQR ModeleChaleur Faible Avec LE Bouton EN Position « SEAR/HI » Avant Dappeler LE Service TechniqueDépannage LE Gril NE Sallume PAS Lorsquon Enfonce LE Bouton DallumagePour Lobtention DU Service DE Garantie Quelle EST LA Durée DE Cette Garantie LIMITÉE? GarantieGarantie Limitée Fisher & Paykel Sengage ÀUtilisation Commerciale Pour Obtenir DES RéparationsAucune Autre Garantie Remarque Page Litho in USA 09/2001