Sterling AF-XXX specifications Parameter 36 Signal Input 2 S2 Setpoint

Page 38

Parameter 36 – Signal Input 2 (S2) Setpoint

When the S2 configuration, parameter 35, is set to one of the jog modes, this parameter defines the jog setpoint in display units. If the drive operating mode is set to Follower Mode, then this parameter is set in RPM units. This allows a follower control to be jogged when the master is stopped.

Parameter 37 – Signal Input 2 (S2) Pulses per Revolution

This is the number of pulses per revolution for the signal input 2 (S2). The drive supports pickups and encoders from 1 to 2048 pulses per revolution.

Parameter 95 – Factory Default Command

When set to a value of 5, the unit will be reset to factory default settings. This can also be achieved by applying power to the unit with both the Enter and Down buttons depressed. The programming jumper must be in the "On" position for this method to function.

Parameter 98 – Save to User Default Area Command

When set to a value of 5, the unit will store all adjustable parameters to the user default area. The user default area is intended to be a location where an end user can store settings specific to their application. Using this, an end user can easily refresh their custom settings in the field if an someone accidentally reconfigures the unit unsuccessfully. Another common use for this area is testing and initial setup. The user can store known-good settings here and easily experiment without the fear of losing the optimal configuration.

Parameter 99 – Restore from User Default Area Command

When set to a value of 1, the unit will restore the all adjustable parameters from the user default area. See parameter 98 for additional information.

Additive Feeders

Chapter 5: Program Parameter Descriptions

38 of 55

Image 38

Contents SF Series Additive Feeders Shipping Information Table of Contents Program Parameter Descriptions Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility RememberAdditive Feeder Safety Tags Maintenance ResponsibilityReporting a Safety Defect Functional Description Standard FeaturesMechanical Features Models Covered in This ManualOptions Electrical FeaturesController Features Accessories Safety Devices and InterlocksFail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs Uncrating the Equipment InstallationSupply System Installation Rigging and Placing the Additive FeederControl Relay Connection Main Power ConnectionElectrical Connections Setup Procedures Determining the Desired Feed Rate110 100 Equipment Needed Calibration ProcedureProcedure Examples Observed Feed RatesStarting Up the Additive Feeder Initial Start-upPre-Startup Checks Shutting Down the Additive FeederOperation Timer ModuleUsed as a Cycle Override Safety Timer Start-upCounter Module Elapsed Time ModuleControl Relay Connection Injection Molding ApplicationsInjection Molding Field Control ProgrammingProgramming Step by Step Guide Resetting the Unit to Un-Programmed StateJP1 Program Enable Jumper Additive Feeders Operation Injection Mode Application Notes Extrusion Applications Extruder Tracking ControlExtruder Tracking Installation and Setup Extruder Tracking EquationValue Mode Running ModeParameter-Selection Mode Resetting the Unit to Un-Programmed State Minimum Input Pulse Rate Input Pulse Signal RequirementsExtruder Tracking Control Application Notes Maximum Input Pulse Rate Minimum and Maximum Percent SetpointsProgram Parameter Descriptions Defining Program ParametersMode 1 Default to Zero Parameter 19 Power-up Value Parameter 35 Signal Input 2 S2 Input Configuration Parameter 36 Signal Input 2 S2 Setpoint Photocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Preventative Maintenance Material Cleanout/ChangeoverRemoving Auger Assembly Corrective MaintenanceAuger Assembly Changeover Installing Auger AssemblyMotor Brush Replacement Introduction TroubleshootingProblem Possible cause Corrective action Problem Possible cause Corrective action Additive Feeders Troubleshooting Annex B Information Technical SpecificationsAppendix Drawings and Diagrams Additive Feeder Specifications and Overall DimensionsTypical Additive Feeder Controllers Spare Parts List Exploded Assembly Drawing Parts ListDetail # Part number Part/assembly description One Component Control Enclosure Parts Identification Returned Material Policy Safety Tag InformationWarranty Returns Credit ReturnsAdditive Feeder Identification Serial Number Tag Company LogoTechnical Assistance Sterling, Inc Th Street New Berlin, WIWorksheet for Charting Feed Rates