Sterling AF-XXX specifications Spare Parts List, Exploded Assembly Drawing Parts List

Page 49

8-3 Spare Parts List

Figure 5: Exploded Assembly Drawing

Figure 6:	Parts List

Detail #	Part number	Part/assembly description
1	A0541207	Supply Hopper, 1.0 Cubic Foot
1	A0541208	Supply Hopper, 2.0 Cubic Foot
2	A0541225	Hopper Cover, Manual Fill
2	A0541226	Hopper Cover with Cutout for .1 Cubic Foot Hopper Loader
2	A0541227	Hopper Cover with Cutout for .25 Cubic Foot Hopper Loader
3	A0541286	Magnetic Stripping for Supply Hopper Cover
4	A0541285	Screw, ¼-20 x ½", HHC, Grade 5
5	A0101190	Lock Washer, ¼"
6	A0541206	Supply Hopper Sight Glass
7	W0012471	Blind Rivet, 3/16"
8	W00052210	Plunger Pin, Retractable
9	A0541201	Material Transfer Tube
10	A0541202	Main Throat, Standard, 6"
10	A0541208	Main Throat, Optional Expanded, 8"
11	A0541205	Main Throat Sight Glass
12	A0069242	Flat Washer, 5/16
13	W00001948	Screw, 3/8-16 x ½"
14	A0069203	Lock Washer, 3/8"
15	A0069458	Screw, 3/8-16 x 3/4"
16	A0541216	Calibration Sample Port Plate
17	A0541215	Clean Out Port Plate
18	A0540904	Screw, 10-32 x ½"

Additive Feeders

Chapter 8: Appendix

49 of 55

Image 49

Contents SF Series Additive Feeders Shipping Information Table of Contents Program Parameter Descriptions How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityMaintenance Responsibility Additive Feeder Safety TagsReporting a Safety Defect Mechanical Features Standard FeaturesFunctional Description Models Covered in This ManualController Features Electrical FeaturesOptions Safety Devices and Interlocks AccessoriesSafety Device Lock-Outs Safety Circuit StandardsFail Safe Operation Supply System Installation InstallationUncrating the Equipment Rigging and Placing the Additive FeederElectrical Connections Main Power ConnectionControl Relay Connection Determining the Desired Feed Rate Setup Procedures110 100 Procedure Calibration ProcedureEquipment Needed Observed Feed Rates ExamplesPre-Startup Checks Initial Start-upStarting Up the Additive Feeder Shutting Down the Additive FeederUsed as a Cycle Override Safety Timer Timer ModuleOperation Start-upElapsed Time Module Counter ModuleInjection Molding Injection Molding ApplicationsControl Relay Connection Field Control ProgrammingJP1 Program Enable Jumper Resetting the Unit to Un-Programmed StateProgramming Step by Step Guide Additive Feeders Operation Injection Mode Application Notes Extruder Tracking Control Extrusion ApplicationsExtruder Tracking Equation Extruder Tracking Installation and SetupParameter-Selection Mode Running ModeValue Mode Resetting the Unit to Un-Programmed State Extruder Tracking Control Application Notes Input Pulse Signal RequirementsMinimum Input Pulse Rate Minimum and Maximum Percent Setpoints Maximum Input Pulse RateDefining Program Parameters Program Parameter DescriptionsMode 1 Default to Zero Parameter 19 Power-up Value Parameter 35 Signal Input 2 S2 Input Configuration Parameter 36 Signal Input 2 S2 Setpoint Preventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Material Cleanout/Changeover Preventative MaintenanceAuger Assembly Changeover Corrective MaintenanceRemoving Auger Assembly Installing Auger AssemblyMotor Brush Replacement Problem Possible cause Corrective action TroubleshootingIntroduction Problem Possible cause Corrective action Additive Feeders Troubleshooting Appendix Technical SpecificationsAnnex B Information Additive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers Exploded Assembly Drawing Parts List Spare Parts ListDetail # Part number Part/assembly description One Component Control Enclosure Parts Identification Warranty Returns Safety Tag InformationReturned Material Policy Credit ReturnsCompany Logo Additive Feeder Identification Serial Number TagSterling, Inc Th Street New Berlin, WI Technical AssistanceWorksheet for Charting Feed Rates