Sterling AF-XXX Drawings and Diagrams, Additive Feeder Specifications and Overall Dimensions

Page 47

8-2 Drawings and Diagrams

Figure 3: Additive Feeder Specifications and Overall Dimensions

MOUNTING FLANGE			CONTROLS
				ADDITIVE FEEDER
		ADDITIVE FEEDER
4"	7"			SET POINT
	91 2"	SET POINT	912"
	91 2"		912"
	POWER	MOTOR
	ON	MOTOR ON AUTO
		OFF		POWER	MOTOR
	OFF	MAN	ON	MOTOR ON	AUTO
					OFF
			OFF		MAN

4"

7"

614"

614"

STANDARD	STANDARD
	WITH OPTIONS

27 34"

12"

183 4"

6"

3114"

Additive Feeder	Hopper capacity	Electrical supply
Type
1 Component	1.0 Cu. Ft.	115-1-60
2 Component	(2) 1.0 Cu. Ft.	115-1-60

Amp draw 1.3 2.5

Shipping weight

50lbs.

90lbs.

Additive Feeders

Chapter 8: Appendix

47 of 55

Image 47

Contents SF Series Additive Feeders Shipping Information Table of Contents Program Parameter Descriptions Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityMaintenance Responsibility Additive Feeder Safety TagsReporting a Safety Defect Models Covered in This Manual Standard FeaturesMechanical Features Functional DescriptionOptions Electrical FeaturesController Features Safety Devices and Interlocks AccessoriesFail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs Rigging and Placing the Additive Feeder InstallationSupply System Installation Uncrating the EquipmentControl Relay Connection Main Power ConnectionElectrical Connections Determining the Desired Feed Rate Setup Procedures110 100 Equipment Needed Calibration ProcedureProcedure Observed Feed Rates ExamplesShutting Down the Additive Feeder Initial Start-upPre-Startup Checks Starting Up the Additive FeederStart-up Timer ModuleUsed as a Cycle Override Safety Timer OperationElapsed Time Module Counter ModuleField Control Programming Injection Molding ApplicationsInjection Molding Control Relay ConnectionProgramming Step by Step Guide Resetting the Unit to Un-Programmed StateJP1 Program Enable Jumper Additive Feeders Operation Injection Mode Application Notes Extruder Tracking Control Extrusion ApplicationsExtruder Tracking Equation Extruder Tracking Installation and SetupValue Mode Running ModeParameter-Selection Mode Resetting the Unit to Un-Programmed State Minimum Input Pulse Rate Input Pulse Signal RequirementsExtruder Tracking Control Application Notes Minimum and Maximum Percent Setpoints Maximum Input Pulse RateDefining Program Parameters Program Parameter DescriptionsMode 1 Default to Zero Parameter 19 Power-up Value Parameter 35 Signal Input 2 S2 Input Configuration Parameter 36 Signal Input 2 S2 Setpoint Photocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Material Cleanout/Changeover Preventative MaintenanceInstalling Auger Assembly Corrective MaintenanceAuger Assembly Changeover Removing Auger AssemblyMotor Brush Replacement Introduction TroubleshootingProblem Possible cause Corrective action Problem Possible cause Corrective action Additive Feeders Troubleshooting Annex B Information Technical SpecificationsAppendix Additive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers Exploded Assembly Drawing Parts List Spare Parts ListDetail # Part number Part/assembly description One Component Control Enclosure Parts Identification Credit Returns Safety Tag InformationWarranty Returns Returned Material PolicyCompany Logo Additive Feeder Identification Serial Number TagSterling, Inc Th Street New Berlin, WI Technical AssistanceWorksheet for Charting Feed Rates