Sterling AF-XXX specifications Detail # Part number Part/assembly description

Page 50

Detail #	Part number	Part/assembly description
19	W00052550	Knob, Knurled
20	A0069218	Stop Nut, 5/16-18
21	A0069549	Flat Washer, 3/8"
22	A0541279	Screw, 5/16-18 x 4½"
23	A0069241	Flat Washer, ¼"
24	A0541277	Quick Release Pin
25	A0541209	Feed Tube Insert, 1/2"
25	A0541210	Feed Tube Insert, 3/4"
25	A0541211	Feed Tube Insert, 1"
25	A0541212	Feed Tube Insert, 1 1/4"
25	A0541213	Feed Tube Insert, 1 1/2"
25	A0541214	Feed Tube Insert, 1 3/4"
26	A0541219	Auger, 1/2"
26	A0541220	Auger, 3/4"
26	A0541219	Auger, 1"
26	A0541292	Auger, 1 1/4"
Assy.	A0541292	Auger Assembly, 1/2" *
Assy.	A0541293	Auger Assembly, 3/4" *
Assy.	A0541294	Auger Assembly, 1" *
Assy.	A0541295	Auger Assembly, 1 1/4" *
Assy.	A0541296	Auger Assembly, 1 1/2"
Assy.	A0541297	Auger Assembly, 1 3/4"
27	W00015504	Roll Pin
28	A0541284	O Ring
29	A0541217	Thrust Bearing
30	A0541283	Compression Spring
31	W00000947	Lock Washer, #10
32	A0103129	Terminal Ring for Retaining Cable
33	W00013647	Pin Retaining Cable
34	A0541229	Motor Mount
35	A0541282	Jaw Coupler
36	A0555661	Motor Assy, 115 VAC, 1/10 H.P.
36	A0541298	Motor Assembly, 115 VAC 1/20 H.P.
36	A0547487	Motor Assembly, 115 VAC, Low RPM 1/20 H.P.
37	A0541265	Control, 115 VAC
37	A0541266	Control, 115 VAC, Timer/Cycle Counter
37	A0541267	Control, 115 VAC, Timer/Elapsed Timer
37	A0541268	Control, 115 VAC, Extruder Tracking
37	A0541269	Control, 115 VAC, Extruder Tracking, Timer/Elapsed Timer
37	A0544795	230 VAC/115 VAC Transformer Control Assembly
38	A0541039	Strain Relief for Control Cable
39	A0541262	Lock Nut for Strain Relief
	A0539035	Transition Flange, Feed Throat, 7" to 4" Square

*Auger assemblies include details 26, 27, 28, 29, 30, & 12. Order the appropriately-sized feed tube insert (Detail 25) if needed.

Additive Feeders

Chapter 8: Appendix

50 of 55

Image 50

Contents SF Series Additive Feeders Shipping Information Table of Contents Program Parameter Descriptions Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility RememberAdditive Feeder Safety Tags Maintenance ResponsibilityReporting a Safety Defect Functional Description Standard FeaturesMechanical Features Models Covered in This ManualOptions Electrical FeaturesController Features Accessories Safety Devices and InterlocksFail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs Uncrating the Equipment InstallationSupply System Installation Rigging and Placing the Additive FeederControl Relay Connection Main Power ConnectionElectrical Connections Setup Procedures Determining the Desired Feed Rate110 100 Equipment Needed Calibration ProcedureProcedure Examples Observed Feed RatesStarting Up the Additive Feeder Initial Start-upPre-Startup Checks Shutting Down the Additive FeederOperation Timer ModuleUsed as a Cycle Override Safety Timer Start-upCounter Module Elapsed Time ModuleControl Relay Connection Injection Molding ApplicationsInjection Molding Field Control ProgrammingProgramming Step by Step Guide Resetting the Unit to Un-Programmed StateJP1 Program Enable Jumper Additive Feeders Operation Injection Mode Application Notes Extrusion Applications Extruder Tracking ControlExtruder Tracking Installation and Setup Extruder Tracking EquationValue Mode Running ModeParameter-Selection Mode Resetting the Unit to Un-Programmed State Minimum Input Pulse Rate Input Pulse Signal RequirementsExtruder Tracking Control Application Notes Maximum Input Pulse Rate Minimum and Maximum Percent SetpointsProgram Parameter Descriptions Defining Program ParametersMode 1 Default to Zero Parameter 19 Power-up Value Parameter 35 Signal Input 2 S2 Input Configuration Parameter 36 Signal Input 2 S2 Setpoint Photocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Preventative Maintenance Material Cleanout/ChangeoverRemoving Auger Assembly Corrective MaintenanceAuger Assembly Changeover Installing Auger AssemblyMotor Brush Replacement Introduction TroubleshootingProblem Possible cause Corrective action Problem Possible cause Corrective action Additive Feeders Troubleshooting Annex B Information Technical SpecificationsAppendix Drawings and Diagrams Additive Feeder Specifications and Overall DimensionsTypical Additive Feeder Controllers Spare Parts List Exploded Assembly Drawing Parts ListDetail # Part number Part/assembly description One Component Control Enclosure Parts Identification Returned Material Policy Safety Tag InformationWarranty Returns Credit ReturnsAdditive Feeder Identification Serial Number Tag Company LogoTechnical Assistance Sterling, Inc Th Street New Berlin, WIWorksheet for Charting Feed Rates