GE 90-70 manual Redundancy CPU, Features

Page 23

2

Redundancy CPU

The redundancy CPUs have been designed specifically for Series 90-70 Hot Standby CPU

Redundancy applications.

Features

The Enhanced Hot Standby CPU supports floating point calculations, offers remote programmer keyswitch memory protection, and has seven status LEDs. Operation of the CPU may be controlled by the three-position RUN/STOP switch on the module, or remotely by an attached programmer. Program and configuration data can be locked through software passwords or manually by the memory protect keyswitch. When the key is in the protected position, a programmer connected to the Bus Transmitter Module can only change program and configuration data.

In a Hot Standby CPU Redundancy system, one CPU is configured as the Primary CPU and the other as the Secondary CPU. The Primary unit and the Secondary unit must each have a Redundancy CPU installed in slot 1 of rack 0.

		Secondary Unit						Primary Unit
P C	B	R G					P C	B	R G
P C	B	R G					P C	B	R G
S P	T	C B					S P	T	C B
U	M M C						U	M M C

	30	31
		Redundancy Communications Link
	CGR935	Redundancy Communications Link
	or	Redundancy Communications Link
	or
	CGR772	Genius Bus
	in these slots	Genius Bus
	in these slots

Not all features of other Series 90-70 CPUs are available in redundancy models. See chapter 4 for details.

2-2

Series 90™-70 Enhanced Hot Standby CPU Redundancy User's Guide – May 2000

GFK-1527A

Image 23

Contents GE Fanuc Automation GFL-002 Related Publications Content of This ManualPreface Preface Contents Contents Chapter Fault Detection Appendix a Cabling Information Definition of Terms IntroductionEnhanced Hot Standby CPU Redundancy Compatibility with CPU780 Using the Redundancy CPU for Non-Redundant OperationDifferences in Operation for Redundancy CPUs Features not Available with Redundancy CPUsRedundancy CPUs as Compared to Other Series 90-70 CPUs Systems for Enhanced Hot Standby CPU Redundancy Enhanced Redundancy CPU ModuleRedundancy Communications Module Redundant RacksCable Connections Genius I/OLocal I/O Local I/0 Can be Enhanced Hot Standby CPU Redundancy System with Local I/OGDB Control Strategy Control StrategiesGHS Control Strategy Output Control with GDB Basic Enhanced Hot Standby OperationOutput Control with GHS Single Bus with Preferred Master GHS Control Strategy Basic CPU Redundancy SetupsCritical Data + Redundant Outputs Transferred Single Bus with Floating Master GDB Control StrategyPaired GBC = INT/EXT Internal External Dual Bus with Floating Master GDB Control StrategyDuplex CPU Redundancy Online ProgrammingOn-Line Repair System Racks For Installation InstructionsSystem Components Redundancy CPU FeaturesExpansion Memory Board Watchdog TimerCPU Architecture CPU LEDs CPU FeaturesMemory Protect Keyswitch Battery ConnectorsPort CPU Mode SwitchUnit Select Pushbutton Redundancy Communications ModuleRCM Status Leds ConnectorBus Transmitter Module Status LEDs ConnectorsBus Transmitter Module Bus Receiver Module Status LEDs Bus Receiver ModuleCables and Termination Location of GBCs and Blocks Genius Bus ControllerDual Bus Genius Networks Single Bus Genius NetworksBus Controller LEDs Program Folders in Control Programming Software Configuration RequirementsProgrammer Connection for Configuration One Application Program in Both PLCsProgram Folders in Logicmaster CPU Configuration ParametersParameter Default Range Description Configuring Shared I/O ReferencesSystem Communications Window Considerations Finding the Memory Available for Application Program StorageBus Controller Configuration Parameters Rack Module Configuration ParametersGenius I/O Block Configuration Parameters Normal Operation Powerup of a Redundant CPU Resynchronization of a Redundant CPU Incompatible ConfigurationsGDB Control Strategy GHS Control StrategyOvrpre %S Reference Not Available References for CPU RedundancySweep Time Synchronization Scan SynchronizationAT a Output Data Transfer to the Backup UnitFail Wait Time Data Transfer TimeGFK-1527A Normal Operation Data Transfer Example Programming a Data Transfer from Backup Unit to Active UnitDisabling Data Transfer Copy in Backup Unit Svcreq #43 Command Block for Svcreq #43 Validating the Backup PLCs Logic Solution Backup Qualification with Svcreq #43Validating the Backup PLCs Input Scan Switching Times Switching Control to the Backup UnitExample 1 Role switches allowed on both units RUN Disabled ModeRUN Disabled Mode for GHS Control Strategy Example 4 Role switches allowed on both units Example 2 Role switches allowed on both unitsExample 3 Role switches not allowed on either unit Backup Active Example 8 Invalid RUN Disabled Mode for GDB Control StrategyCGR772 CGR935 Finding the Words to Checksum Each SweepFinding the Total Sweep Time Finding the Background Window TimeMultiple I/O Scan Sets Timer and PID Function BlocksMiscellaneous Operation Information Timed ContactsBackground Window Time Stop to RUN Mode TransitionSequential Function Chart Programming SFC DebuggerGenius Bus Controller Switching Ethernet Global Data Consumption Ethernet Global Data in a Redundancy CPUSntp Timestamping Ethernet Global Data ProductionConfiguration of Fault Actions Fault DetectionFault Detection Message Fault Description Corrective Action PLC Fault Table Messages for RedundancyWith redundancy in other fault groups Fault Response Losing a Link Faulting the Redundancy Communications ModuleFault Actions in a CPU Redundancy System Fault Group Type Description Configurable FaultsFatal Faults on Both Units in the Same Sweep Non-Configurable Fault GroupOn-Line Repair Racks Power SupplyMaintaining Parallel Bus Termination On-Line Repair RecommendationsRedundancy Communications Link Failures Central Processor UnitRedundancy Communications Module and Cables Genius Bus Single Bus Networks Bus faultsBus Transmitter Module Genius Bus ControllerGenius Blocks Dual Bus NetworksPurpose SpecificationsCabling Information IC690CBL714A Multi-drop CableConnector a Connector A, 15-pin Female Index Battery connectors Bus Controller, GeniusIndex Online programming Online repair Svcreq