Kirby 37 appendix Install the o-ring in the bent tube adapter, 108

Page 41

Kirby Morgan 37 & 57

26)Inert the adjustment nipple into the main tube on the end opposite end from the adjustment knob. Using a flat blade screwdriver, thread the nipple into the tube slowly.

As soon as you see any movement of the lever stop screwing the nipple in. Turn in on the flex knob until an audible click is heard.

27)It is recommended that the regulator sit for 24 hours before any further assembly is completed. This will allow the seat to conform itself correctly to the inlet nipple.

28)Bend the lever down and carefully install this assembly of the main tube and adjustment knob into the regulator until the threaded end of this assembly comes completely through the opposite side of the regulator body.

29)Install the o-ring and the bent tube adapter and tighten to 30 inch pounds.

30)Tighten the packing nut at the flex knob with a one inch wrench to 30 inch pounds.

31)Install the lock clip on the main tube.

32)Adjust the regulator per this chapter.

33)Reinstall the diaphragm, cover and cover retain- ing ring.

34)Reinstall the bent tube assembly as per this chapter.

35)Once the regulator is properly adjusted, reinstall the washers and screws that secure the regulator cover and ring. Tighten the screws to 12 inch pounds.

Install the o-ring in the bent tube adapter.

108	© Copyright 1970-2008 Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 080508001

Image 41

Contents Kirby Morgan 37 IntroductionOne Way Valve Tighten to 150 inch lbs Newton Meters with a torque wrench Correct assembly order of the one way valveSide Block Assembly Removal Side Block AssemblySeparating the Side Block Assembly from the Helmet Shell GeneralAir Train Gasket Thin putty knife helps to remove the side blockComponents of the Side Block & Air Train Diver cannot use the free flow system as Could lead to drowningSource of breathing air. This could lead To suffocationCleaning and Lubricating Disassembly of the Defogger ValveClean all the metal parts to remove salts Defogger ValveReassembly of the Defogger Valve Side Block assembly and it’s associated partsRemove the valve stem Emergency Valve AssemblyValve Body Valve Stem Washer Packing nut Reassembly of Emergency ValvePacking Knob Lock nut Spring Leak Testing the EGS Valve Inspection of Bent Tube Assembly Bent Tube AssemblyRemoval of the Bent Tube Assembly Kirby Morgan 37 Installation Bent Tube Assembly Tool Kit with pouch SuperFlow Demand RegulatorGeneral Regulator Information Remove the demand regulator clamp Screw the regulator adjustment knob out for removalInspect the washer and o-ring Reassembly of the SuperFlow 350 Regulator Adjustment SystemShake out the spacer, spring set, and piston Regulator mount nut must be removed to remove the regulator SuperFlow 350 Demand Regulator Removal from HelmetDemand Regulator Kirby Morgan 37 Disassembly of the SuperFlowSuperFlow 350 regulator assembly Castle Wrench and inlet valve Demand Regulator Parts Kirby Morgan 37 Inspection of SuperFlowUse silicone sealant On the silicone sealant tube and MaterialPage Valve seat Adjustment end of the SuperFlow 350 regulator Install the retaining pin in the adjustment knobKirby Morgan 37 Test the response of the purge button Kirby Morgan 37 Tuning the SuperFlow 350 RegulatorUse the disk end of the Kmdsi wrench to bend the lever down Page Press the cover over the diaphragm Oral Nasal General Information Oral/NasalOral/Nasal Removal Inspection of Oral/NasalKirby Morgan 37 Oral/Nasal Replacement Exploded view of the Quad-Valve exhaust system Quad-Valve Exhaust AssemblyQuad-Valve Assembly Removal Page Whiskers must be aligned properly on the exhaust main body SuperFlow Regulator Exhaust Valve ReplacementQuad-Valve Assembly Installation Water Dump Exhaust Body Water Dump Valve ReplacementWater Dump Valve Body Removal Water Dump Valve Removal101 Reinstalling the Quad-Valve Exhaust Assembly102 SuperFlow Stainless Balanced Regulator103 Kirby Morgan 37 Adjusting the SuperFlowRemove the bent tube and the bent tube adapter 104 105 Bent tube adapterExploded view of SuperFlow 450 regulator 106 107 108 Install the o-ring in the bent tube adapter109 Kirby Morgan 37 SuperFlow 450 Regulator RemovalBe sure to remove and set aside the whisker spacers 110 Kirby Morgan 37 SuperFlow 450 DisassemblySuperFlow 450 flex knob assembly 111 RingDetails of the SuperFlow 450 main tube and associated parts SuperFlow 450 Regulator Kirby Morgan 37 AssemblyRegulator Body Exhaust valve insert Retainer ring113 Install the inlet valve in the main tube114 115 Tighten the cover hand tightMake sure the lock clip fully engages the packing nut 116 Kirby Morgan 37 SuperFlow 450 Regulator Installation117