Linear PERS-4200 Series manual Sensor Learn / Test Mode, Learning Sensors

Page 31

13. Sensor Learn / Test Mode

Wireless transmitters are called “sensors” in the PERS vocabulary. In Learn / Test Mode the Console can learn new sensors, test sensors, and erase all sensors.

✓NOTE: While in Learn /Test Mode, all normal operations of PERS-4200 Console are suspended. No alarms or reports are made in this mode.

To exit this mode, press and release the CANCEL button. The Console will exit Learn / Test Mode automatically after three minutes of no activity (including RF activity from a learned sensor, which will extend Learn / Test Mode for an additional 3 minutes).

13.1 Learning Sensors

The Console can “learn” up to 16 sensors. Use the following steps to locally learn sensors into the Console:

1.Press and release the TEST button (located recessed on the bottom of the Console). The Console will announce:

0“Test Mode, ﬁrmware version [number]...

hardware version [number]”.

2.Press and release the TEST button again. The Console will announce:

0“Ready to learn sensor... Zone [number]”.

3.Activate the sensor to learn. The Console will announce:

0“[Fire, Activity, Emergency, or Carbon Monoxide] sensor learned”.

4. The Console will announce the next available zone number:

0 “Ready to learn sensor... Zone [number]”.

To advance to the next available zone without learning a sensor, press the TEST button. Zones already programmed with a sensor are skipped.

5. Repeat Step 3 for each additional sensor (up to 16 total). When all zone locations are full, the Console will announce:

0 “Zones full”

After Zone 16 has been skipped or learned, if there are any available zones remaining, the learn sequence will advance to the ﬁ rst available skipped zone and allow learning another sensor. The learn sequence will cycle through any available/skipped zones until either all zones are programmed, or Learn / Test Mode is exited.

✓ NOTE: To exit Learn /Test Mode at any time, press the CANCEL button.

1.PRESS TEST BUTTON, CONSOLE WILL ANNOUNCE VERSION

TEST BUTTON	2.	PRESS TEST BUTTON AGAIN
	2.	PRESS TEST BUTTON AGAIN
	3. CONSOLE WILL ANNOUNCE READY TO LEARN AND ZONE NUMBER
	4.	ACTIVATE SENSOR
	5.	CONSOLE WILL ANNOUNCE SENSOR LEARNED
	6. REPEAT FOR ADDITIONAL SENSORS, OR PRESS CANCEL TO EXIT

BOTTOM OF PERS-4200 CONSOLE

Learning Multiple Sensors

29

Image 31

Contents PERS-4200 Series Important Pers Installation Warnings Contents Programming Power SupplyProduct Description Voice PromptsFire Operation SummaryEmergency ActivityAlternate Console Labels Remote Speaker/Microphone ModuleHome Button Cover Telephone Connections Option Module InstallationPower Supply Installation Console ConnectionsProvider Features Console Modes & FeaturesProvider Modes User Modes User FeaturesProgramming Mode Using the Provider ModesPower Off Mode Not-Ready ModeRA4200 can connect to the Console two ways Programming with RA4200Software Description System RequirementsProgramming Outline RA4200 Software InstallationTo Test the Modem in Windows XP Testing the ModemCommand and Response modem information. If the modem is not Working properly, Windows will notify youAccount Template Tabs 10. RA4200 Software OverviewMenu Bar Sub-menus that can be accessed from the Menu Bar areDrop-down Menu Items and Icons Customer Tab Console Tab Annunciate Status with Home Button Temperature Limit SettingsConsole Time Settings Annunciate Trouble IndicationSensors Tab Low Battery Report OptionsSensor Zones Sensor Status IndicatorsSensor types selections available are Communicator Fallback Communicator TabPstn Dialing Sequence Three Central Station IP reporting formats are available Internet Protocol IP ReportingEnter the account number for the speciﬁ c Console Three Central Station Pstn reporting formats are availableReport Supervisory Events Mode Switch ReportingReporting Options Tab Report AC FailAutomatic Status Reports Speaker Phone TimerTwo-way Audio Mode 2 Alarm CodesReport Missed Reminder Reminder SettingsAudio Replay During Timeout Reminder Messages TabFour types of reminder messages are available Reminder Time Slot SettingsCreating or Editing Reminder Messages Test ReminderChoose a reminder message type Send/Receive Window Console CommunicationFirst Time Programming for New Consoles When a Console is new or un-programmed it will announceSending and Receiving Console Data Console Time and DateOption 2 Primary Telephone Number Connecting with the ConsoleLimited Remote Telephone Programming Option 1 Reporting FormatConsole will announce the next available zone number Sensor Learn / Test ModeLearning Sensors Activate the sensor to learn. The Console will announceLearning a Single Sensor Testing SensorsErasing All Sensors Clearing the Event Log Event LogRetrieving the Event Log Printing the Event LogPrinting or Exporting a Template Firmware Update Utility Instructions System Firmware Update Utility InstructionsUpdating Console Firmware Upgrade Complete Reporting Code CID Appendix a Reporting CodesSystem Event Appendix B Mode TableOpening Port COM30 Appendix C Communications Status Window TableSpeciﬁcations Power RequirementsRegulatory Information Linear Limited Warranty#’s IndexSIM ID Copyright 2014 Linear LLC 237016 a