Leica dm750 p manual Instructions on use, Intended use, Place of use, Non-intended use

Page 8

Instructions on use

Intended use

The Leica DM750 P microscope is an optical instrument which uses magnification and illu- mination to improve the visibility of objects. It is used for observing and documenting.

The Leica DM750 P microscope may be used only in closed rooms and must be placed on a solid floor.

The Leica DM750 P microscope can be used in clean rooms without any problems.

Position the Leica DM750 P microscope so that it can be disconnected from the

power supply at any time. The power cord must remain accessible at all times.

Place of use

Only use the instruments in closed, dust free rooms and between +10  °C and +40  °C. Protect the devices from oil, chemicals and extreme humidity. If using the devices outdoors, protect them from dust and moisture. Never use electri- cal devices outdoors. Install electrical devices at least 10 cm from the wall and away from flam- mable substances.

Avoid large temperature fluctuations, direct sunlight and vibrations. These conditions can distort measurements and micrographic images.

In warm and warm-damp climatic zones, the individual components require special care in order to prevent the build-up of

fungus.

Non-intended use

Using the instrument in any way contrary to the specifications in the user

manual can lead to bodily harm and damage to objects. Doing so can impair the functions of the protective measures provided.

Never install any other plug (NEMA 5-15P) or unscrew any mechanical components unless expressly instructed to do

so in the instructions.

The devices and accessories described in this operating manual have been tested

for safety and potential hazards.

Leica DM750 P

Manual

8

 

 

 

Image 8
Contents Leica DM750 P Manual Chapter overview Contents Safety regulations Safety concept Symbols used in this operating manual Light bulbsImportant information Provide clarityImportant Notes DescriptionContact address EC Declaration of ConformityInstructions on use Intended usePlace of use Non-intended useTo any warranty claims TransportDisposal Integration in third-party productsHealth risks and dangers of use Health risksViral infections of the eye Vidual or detachable eyecupsInformation for the person responsible for the instrument Information for the person responsible for the instrumentCleaning coated parts and plastic parts Cleaning glass surfacesCare instructions General instructionsAccessories, maintenance and repair AccessoriesMaintenance Repairs and service workFuse Replacement Electrical dataInput 100-240 V, 50/60 Hz, 5 W 3 W LED EnvironmentLeica DM750 P Introduction Check the components against the planned configuration UnpackingGet Ready Attaching Analyzer Module or Analyzer/Bertrand Lens Module Tools usedViewing Tube Installing Objectives Substage Condenser Substage CondenserCompletely loosen the two thumbscrews on the condenser mount Get Set Work Surface Basic setupPower Using the Aperture Condenser ObjectivePolarizer Setting up Polarized LightSubstage condenser in a swing in/out Analyzer into position Focusing FocusingViewing Tube Adjustment Slot of the right eyetubeEyepiece. Do not raise or lower the stage to focus Slightly, if at allKoehler Set up Koehler Set upFocus the polarizing sample Objective CentrationϘϘ Centering keys Modules You can now view the conoscopic image through the eyepieces Bertrand Lens OperationImage through the eyepieces Or Disabled and you will not see any blinking Time Delay ShutoffChanging the status of the time delay shutoff Leica DM750 P Manual Ready! Set! Go Care of the Microscope General maintenance GeneralHands. There is a handle on the back Is extended This purpose For two compensators in the rearLint-free cloth, lens tissue or cotton swab ϘϘ It is very important to avoid the excessiveShould be moistened with solvent, but Around the lensMechanical Maintenance Mechanical MaintenanceDimensions Leica DM750 P Manual Leica DM750 P Manual Leica DM750 P Manual