Phonetics 1104 Be sure to use alkaline batteries-do not, Use rechargeable nicad batteries

Page 102

102

Other Monitoring:

Problem	Cause	Solution
(continued from previous page)
5. The batteries drain prematurely.	The unit’s AC transformer is unplugged or for	The batteries will take over powering the unit
	some other reason, full AC power is not avail-	when the AC transformer is unplugged from
	able to the unit.	the 120 VAC outlet. When storing the unit, be
		sure to remove the batteries.
		Refer to Chapter 2, Section 2.4.
		Be sure to use alkaline batteries—do not
		use rechargeable nicad batteries.

If the solutions offered above do not appear to correct the problem, apply the following steps, in the order shown.

•Remove the batteries.

•Unplug the unit.

•Wait one minute for the Model 1104 to completely power down.

•Plug in the unit’s AC adaptor into a standard 120 VAC outlet.

•Replace the batteries.

Sensaphone® Model 1104 User’s Manual

Refer to Chapter 2, Installation, for additional information on batteries and installation procedures.

Image 102

Contents Model SENSAPHONE, INC Important Safety Instructions Sensaphone Model 1104 User’s Manual FCC Requirements PHONETICS, INCSensaphone Model 1104 User’s Manual Canadian Department of Communications Statement Sensaphone Model 1104 User’s Manual Viii Summary of the Alarm Dial-Out Process Technical SupportTone or Pulse Dialing Special Dialing Unit ID NumberDial-out Telephone Numbers Rings Until AnswerEstablishing High and Low Temperature Limits Input ConfigurationEnable/Disable Inputs Temperature ScaleAlarm Acknowledgment High Sound Alarm Enable/DisableExit Delay Status ReportIntroduction Technical Support Installation Operating Environment+ + + RUN Installing the Telephone Line Alert Inputs Sensor Connected to an Alert Input Two Sensors Wired to Adjacent Inputs ~ ~ Disconnecting the Model 1104 for Storage or Seasonal Use From the unit completely to avoid damage to the circuitrySensaphone Model 1104 User’s Manual Quick Start Local KeypadSet Configuration of Inputs RUNStatus Set the ID NumberSet Dial-Out Telephone Numbers NumberSet Temperature Limits Model 1104 responds Enter low temperature limitModel 1104 responds Enter high temperature limit Quick Start Action-Response Programmable Feature Alert ConditionCommunications Programming Programming the ID NumberHello, this is telephone number Unit ID Number Interrogating the ID Number Programming Dial-out Telephone Numbers Enter numberInterrogating a Dial-out Telephone Number Erasing a Telephone NumberPress ENTER. The Model 1104 will say Enter Tone or Pulse Dialing Special Dialing KeysPause Asterisk Incorporating a PausePound # CodeIncorporating a Pound # or Asterisk PressedPress any unassigned number key from 1 to 4 to represent Special Dialing to a Beeper or Pager Now press Pause once to activate a four second delay. This Programming Rings Until Answer Interrogating Rings Until AnswerTAD Enable/Disable Using the TAD FeatureNo TAD In Use Programming the Listen-in Time Interrogating the Listen-in Time Call Delay Programming the Call DelayInterrogating Call Delay Enable/Disable Local Voice Mute Local Voice MuteProgramming Voice Repetitions 10.2 Interrogating Voice RepetitionsModel 1104 will recite the number programmed Programming Intercall Time Interrogating Intercall Time SecondsProgramming Max Calls Interrogating Max Calls Setting the Clock Interrogating for the Current Time Locking the Keypad Unlocking the KeypadUsing the number keys, enter the digits for the code Sensaphone Model 1104 User’s Manual Alarm Programming Programming Input Configuration StatusVerifying Input Configuration Changing Enabled/Disabled Input StatusVerifying Enabled/Disabled Input Status Programming Input Recognition Time Immediately follows the number recited for that inputInterrogating Input Recognition Time Recites the digits as they are pressedPress the corresponding input key 1 to Programming Temperature Limits for a Selected Input Disabling Alarm Response to High or Low Temperature Interrogating High and Low Temperature LimitsTemperature Calibration Programming Temperature Calibration Interrogating Temperature CalibrationObtaining Current Temperature Enabling/Disabling the AC Power Alarm Programming Power Failure Recognition Time Model 1104 will recite the digits as they are pressedInterrogating Power Failure Recognition Time Programming Sound Alarm Sensitivity Using the number keys, enter a value for sound sensitivityProgramming High Sound Alarm Recognition Time Interrogating Sound SensitivityChanging Enabled/Disabled High Sound Alarm Exit Delay Acknowledgment Status Report & Remote Access Local AcknowledgmentTouch-Tone Acknowledgment Callback Acknowledgment Example Status Report, No Alarms Example Status Report, Existing Alarms Example Status Report, Disabled Inputs Battery ConditionRemote Access by Touch-Tone Telephone Battery Condition OK, if over 8.2 VoltsReplace batteries, if below 7.2 Volts Activating Status Report Sensaphone Model 1104 User’s Manual Alarm Detection, Dial-out and Acknowledgment OperationCall Delay TemperatureValid Alarm Alarm MessageVoice Repetitions Alarm MessagesIntercall Time Call ProgressTouch-Tone Local, On-siteAcknowledgment Fast CodeTAD Enabled Number...the last number it dialedHave a good day Example a Dial-out Telephone Call Appendix a Troubleshooting Communications / Dial-out ProblemSolution CauseAppendix a Troubleshooting Communications / Dial-out Problem Cause Solution Temperature Monitoring Problem Cause Solution Sound Level Monitoring Problem Cause Solution Other Monitoring Problem Cause Solution101 Appendix a Troubleshooting Be sure to use alkaline batteries-do not Use rechargeable nicad batteriesAppendix B Weekly Testing Procedure 104 Appendix C Accessories Part Number Sensor / SwitchSensaphone Model 1104 User’s Manual 106 Service Department Appendix D Returning the Unit for RepairYear Limited Warranty