Phonetics 1104 user manual Incorporating a Pound # or Asterisk, Pressed

Page 40

Sensaphone® Model 1104 User’s Manual

3.Press any unassigned number key (from 1 to 4) to represent the new telephone number entry. Model 1104 will respond: “Enter number.”

1

CALL

DELAY

4

MAX CALLS

2

VOICE

REPS

3

INTERCALL

TIME

4.From the number keys, enter the access digit (i.e., 9). The Model 1104 will recite the digit.

1

CALL

DELAY

4

MAX CALLS

7

RECOGNITION

TIME

2

VOICE

REPS

5

TEMP LIMITS

8

CLOCK

0

ID NUMBER

POWER

3

INTERCALL

TIME

6

CALIBRATE

9

LISTEN TIME

SOUND

5.	Press PAUSE. The Model 1104 will “beep.”
	RING/TAD
	PAUSE
	AM
6.	Enter the complete telephone number (1 + area code) using the
number keys. The Model 1104 will recite the digits as they are
pressed.

1

CALL

DELAY

4

MAX CALLS

7

RECOGNITION

TIME

2

VOICE

REPS

5

TEMP LIMITS

8

CLOCK

0

ID NUMBER

POWER

3

INTERCALL

TIME

6

CALIBRATE

9

LISTEN TIME

SOUND

	7. Press ENTER. The Model 1104 will say “Enter.”
	ENTER
	TONE
	PM
4.4.3	Incorporating a Pound (#) or Asterisk (*)

Incorporate a pound or asterisk if it is normally included in telephone number:

40

Image 40

Contents Model SENSAPHONE, INC Important Safety Instructions Sensaphone Model 1104 User’s Manual FCC Requirements PHONETICS, INCSensaphone Model 1104 User’s Manual Canadian Department of Communications Statement Sensaphone Model 1104 User’s Manual Viii Summary of the Alarm Dial-Out Process Technical SupportUnit ID Number Dial-out Telephone NumbersTone or Pulse Dialing Special Dialing Rings Until AnswerInput Configuration Enable/Disable InputsEstablishing High and Low Temperature Limits Temperature ScaleHigh Sound Alarm Enable/Disable Exit DelayAlarm Acknowledgment Status ReportIntroduction Technical Support Installation Operating Environment+ + + RUN Installing the Telephone Line Alert Inputs Sensor Connected to an Alert Input Two Sensors Wired to Adjacent Inputs ~ ~ Disconnecting the Model 1104 for Storage or Seasonal Use From the unit completely to avoid damage to the circuitrySensaphone Model 1104 User’s Manual Quick Start Local KeypadSet Configuration of Inputs RUNStatus Set the ID NumberSet Dial-Out Telephone Numbers NumberSet Temperature Limits Model 1104 responds Enter low temperature limitModel 1104 responds Enter high temperature limit Quick Start Action-Response Programmable Feature Alert ConditionProgramming the ID Number Communications ProgrammingHello, this is telephone number Unit ID Number Interrogating the ID Number Programming Dial-out Telephone Numbers Enter numberInterrogating a Dial-out Telephone Number Erasing a Telephone NumberPress ENTER. The Model 1104 will say Enter Special Dialing Keys Tone or Pulse DialingPause Incorporating a Pause Pound #Asterisk CodeIncorporating a Pound # or Asterisk PressedPress any unassigned number key from 1 to 4 to represent Special Dialing to a Beeper or Pager Now press Pause once to activate a four second delay. This Programming Rings Until Answer Interrogating Rings Until AnswerTAD Enable/Disable Using the TAD FeatureNo TAD In Use Programming the Listen-in Time Interrogating the Listen-in Time Call Delay Programming the Call DelayInterrogating Call Delay Enable/Disable Local Voice Mute Local Voice MuteProgramming Voice Repetitions 10.2 Interrogating Voice RepetitionsModel 1104 will recite the number programmed Programming Intercall Time Interrogating Intercall Time SecondsProgramming Max Calls Interrogating Max Calls Setting the Clock Interrogating for the Current Time Locking the Keypad Unlocking the KeypadUsing the number keys, enter the digits for the code Sensaphone Model 1104 User’s Manual Alarm Programming Programming Input Configuration StatusChanging Enabled/Disabled Input Status Verifying Input ConfigurationVerifying Enabled/Disabled Input Status Programming Input Recognition Time Immediately follows the number recited for that inputInterrogating Input Recognition Time Recites the digits as they are pressedPress the corresponding input key 1 to Programming Temperature Limits for a Selected Input Disabling Alarm Response to High or Low Temperature Interrogating High and Low Temperature LimitsTemperature Calibration Programming Temperature Calibration Interrogating Temperature CalibrationObtaining Current Temperature Enabling/Disabling the AC Power Alarm Programming Power Failure Recognition Time Model 1104 will recite the digits as they are pressedInterrogating Power Failure Recognition Time Programming Sound Alarm Sensitivity Using the number keys, enter a value for sound sensitivityProgramming High Sound Alarm Recognition Time Interrogating Sound SensitivityChanging Enabled/Disabled High Sound Alarm Exit Delay Local Acknowledgment Acknowledgment Status Report & Remote AccessTouch-Tone Acknowledgment Callback Acknowledgment Example Status Report, No Alarms Example Status Report, Existing Alarms Example Status Report, Disabled Inputs Battery ConditionBattery Condition OK, if over 8.2 Volts Remote Access by Touch-Tone TelephoneReplace batteries, if below 7.2 Volts Activating Status Report Sensaphone Model 1104 User’s Manual Alarm Detection, Dial-out and Acknowledgment OperationTemperature Valid AlarmCall Delay Alarm MessageAlarm Messages Intercall TimeVoice Repetitions Call ProgressLocal, On-site AcknowledgmentTouch-Tone Fast CodeNumber...the last number it dialed TAD EnabledHave a good day Example a Dial-out Telephone Call Appendix a Troubleshooting Problem SolutionCommunications / Dial-out CauseAppendix a Troubleshooting Communications / Dial-out Problem Cause Solution Temperature Monitoring Problem Cause Solution Sound Level Monitoring Problem Cause Solution Other Monitoring Problem Cause Solution101 Appendix a Troubleshooting Be sure to use alkaline batteries-do not Use rechargeable nicad batteriesAppendix B Weekly Testing Procedure 104 Appendix C Accessories Part Number Sensor / SwitchSensaphone Model 1104 User’s Manual 106 Service Department Appendix D Returning the Unit for RepairYear Limited Warranty