Phonetics Comprehensive Sensaphone Manual for Enhanced Communications and Dial-out Functionality
Page 98

98

Communications / Dial-out:

Problem

Cause

Solution

(Continued from previous page)

You did not allow the telephone to ring

When calling the Model 1104, and the TAD is

 

 

10 times. Note: If the TAD (telephone answer-

disabled, allow the telephone to ring 10 times.

3.

The Model 1104 will not answer the

ing device) is disabled, the telephone rings ten

Refer to Chapter 6, Section 6.1.3, and Chapter

 

telephone for Callback

times before the Model 1104 answers. If the

4, Section 4.6.3.

 

Acknowledgement.

TAD is enabled, the telephone rings once

 

 

 

before the Model 1104 answers the call.

 

 

 

 

 

4.

The Model 1104 recites the alarm

The local voice mute feature is in effect.

Deactivate local voice mute.

 

message or Status Report over the

 

Refer to the programming steps in Chapter 4,

 

telephone, but is silent at the installation

 

Section 4.9.

 

site.

 

 

 

 

 

 

5.

The Model 1104 dials out correctly but

Voice Reps is set to zero.

Reprogram Voice Reps to 1 or greater.

 

fails to audibly recite its alarm message

 

Refer to Chapter 4, Section 4.10.

 

when you answer the call.

 

 

 

 

 

 

6.

The Model 1104 and telephone answering

The Model 1104’s number of Rings Until

Change the number of Rings Until Answer for

 

device (sharing the same line) answer

Answer is set to equal the number of rings set

the Model 1104.

 

incoming calls simultaneously.

for the telephone answering device.

Refer to Chapter 4, Section 4.5.

 

 

 

 

Sensaphone® Model 1104 User’s Manual

Page 97 Page 99
Image 98
Page 97 Page 99
Contents Model SENSAPHONE, INC Important Safety Instructions Sensaphone Model 1104 User’s Manual FCC Requirements PHONETICS, INCSensaphone Model 1104 User’s Manual Canadian Department of Communications Statement Sensaphone Model 1104 User’s Manual Viii Summary of the Alarm Dial-Out Process Technical SupportTone or Pulse Dialing Special Dialing Unit ID NumberDial-out Telephone Numbers Rings Until AnswerEstablishing High and Low Temperature Limits Input ConfigurationEnable/Disable Inputs Temperature ScaleAlarm Acknowledgment High Sound Alarm Enable/DisableExit Delay Status ReportIntroduction Technical Support Installation Operating Environment+ + + RUN Installing the Telephone Line Alert Inputs Sensor Connected to an Alert Input Two Sensors Wired to Adjacent Inputs ~ ~ Disconnecting the Model 1104 for Storage or Seasonal Use From the unit completely to avoid damage to the circuitrySensaphone Model 1104 User’s Manual Quick Start Local KeypadSet Configuration of Inputs RUNStatus Set the ID NumberSet Dial-Out Telephone Numbers NumberSet Temperature Limits Model 1104 responds Enter low temperature limitModel 1104 responds Enter high temperature limit Quick Start Action-Response Programmable Feature Alert ConditionHello, this is telephone number Unit ID Number Communications ProgrammingProgramming the ID Number Interrogating the ID Number Programming Dial-out Telephone Numbers Enter numberInterrogating a Dial-out Telephone Number Erasing a Telephone NumberPress ENTER. The Model 1104 will say Enter Pause Tone or Pulse DialingSpecial Dialing Keys Asterisk Incorporating a PausePound # CodeIncorporating a Pound # or Asterisk PressedPress any unassigned number key from 1 to 4 to represent Special Dialing to a Beeper or Pager Now press Pause once to activate a four second delay. This Programming Rings Until Answer Interrogating Rings Until AnswerTAD Enable/Disable Using the TAD FeatureNo TAD In Use Programming the Listen-in Time Interrogating the Listen-in Time Call Delay Programming the Call DelayInterrogating Call Delay Enable/Disable Local Voice Mute Local Voice MuteProgramming Voice Repetitions 10.2 Interrogating Voice RepetitionsModel 1104 will recite the number programmed Programming Intercall Time Interrogating Intercall Time SecondsProgramming Max Calls Interrogating Max Calls Setting the Clock Interrogating for the Current Time Locking the Keypad Unlocking the KeypadUsing the number keys, enter the digits for the code Sensaphone Model 1104 User’s Manual Alarm Programming Programming Input Configuration StatusVerifying Enabled/Disabled Input Status Verifying Input ConfigurationChanging Enabled/Disabled Input Status Programming Input Recognition Time Immediately follows the number recited for that inputInterrogating Input Recognition Time Recites the digits as they are pressedPress the corresponding input key 1 to Programming Temperature Limits for a Selected Input Disabling Alarm Response to High or Low Temperature Interrogating High and Low Temperature LimitsTemperature Calibration Programming Temperature Calibration Interrogating Temperature CalibrationObtaining Current Temperature Enabling/Disabling the AC Power Alarm Programming Power Failure Recognition Time Model 1104 will recite the digits as they are pressedInterrogating Power Failure Recognition Time Programming Sound Alarm Sensitivity Using the number keys, enter a value for sound sensitivityProgramming High Sound Alarm Recognition Time Interrogating Sound SensitivityChanging Enabled/Disabled High Sound Alarm Exit Delay Touch-Tone Acknowledgment Acknowledgment Status Report & Remote AccessLocal Acknowledgment Callback Acknowledgment Example Status Report, No Alarms Example Status Report, Existing Alarms Example Status Report, Disabled Inputs Battery ConditionReplace batteries, if below 7.2 Volts Remote Access by Touch-Tone TelephoneBattery Condition OK, if over 8.2 Volts Activating Status Report Sensaphone Model 1104 User’s Manual Alarm Detection, Dial-out and Acknowledgment OperationCall Delay TemperatureValid Alarm Alarm MessageVoice Repetitions Alarm MessagesIntercall Time Call ProgressTouch-Tone Local, On-siteAcknowledgment Fast CodeHave a good day TAD EnabledNumber...the last number it dialed Example a Dial-out Telephone Call Appendix a Troubleshooting Communications / Dial-out ProblemSolution CauseAppendix a Troubleshooting Communications / Dial-out Problem Cause Solution Temperature Monitoring Problem Cause Solution Sound Level Monitoring Problem Cause Solution Other Monitoring Problem Cause Solution101 Appendix a Troubleshooting Be sure to use alkaline batteries-do not Use rechargeable nicad batteriesAppendix B Weekly Testing Procedure 104 Appendix C Accessories Part Number Sensor / SwitchSensaphone Model 1104 User’s Manual 106 Service Department Appendix D Returning the Unit for RepairYear Limited Warranty
Top Page Image Contents