Phonetics 1104 user manual Sensor Connected to an Alert Input

Page 20

Sensaphone® Model 1104 User’s Manual

of sensor connected to each alert input (refer to Chapter 5, Section 5.1).

An input configured as “temperature” is designed to evaluate a range of settings. The Model 1104 will read the temperature at the sensor’s location and compare that value to programmed high and low temperature limits. Temperature inputs must be used with Phonetics Remote Temperature Sensor.

NOTE

Before wiring, it is advisable to disable the inputs to prevent accidentally tripping an alarm. See Chapter 5, Section 5.2.

2.10 Installing the Sensor

After you have selected the sensor, loosen the screw of the alert input and its corresponding ground. Two wire leads are used to connect any monitoring sensor. Fasten one lead to the numbered screw and the other lead to GND. Tighten both screws. If the input was not disabled, the Model 1104 may recite its “Alert Condition Exists” message as you connect the sensor. If it does, just press any key to stop it. Re-enable the input after wiring. Refer to Figures 2-6 and 2-7 for connecting a sensor to an alert input.

GND

1

GND

2

GND

3

GND

4

Sensor wired to

Alert Input 3

Figure 2-6. Sensor Connected to an Alert Input

Any sensor can be attached to the Model 1104 using 22-gauge wire. The sensor can be several hundred feet from the unit, as long as the total resistance of the circuit is not greater than 50 ohms. Use wire appropriate for the application.

20

Image 20

Contents Model SENSAPHONE, INC Important Safety Instructions Sensaphone Model 1104 User’s Manual FCC Requirements PHONETICS, INCSensaphone Model 1104 User’s Manual Canadian Department of Communications Statement Sensaphone Model 1104 User’s Manual Viii Summary of the Alarm Dial-Out Process Technical SupportUnit ID Number Dial-out Telephone NumbersTone or Pulse Dialing Special Dialing Rings Until AnswerInput Configuration Enable/Disable InputsEstablishing High and Low Temperature Limits Temperature ScaleHigh Sound Alarm Enable/Disable Exit DelayAlarm Acknowledgment Status ReportIntroduction Technical Support Installation Operating Environment+ + + RUN Installing the Telephone Line Alert Inputs Sensor Connected to an Alert Input Two Sensors Wired to Adjacent Inputs ~ ~ Disconnecting the Model 1104 for Storage or Seasonal Use From the unit completely to avoid damage to the circuitrySensaphone Model 1104 User’s Manual Quick Start Local KeypadSet Configuration of Inputs RUNStatus Set the ID NumberSet Dial-Out Telephone Numbers NumberSet Temperature Limits Model 1104 responds Enter low temperature limitModel 1104 responds Enter high temperature limit Quick Start Action-Response Programmable Feature Alert ConditionHello, this is telephone number Unit ID Number Communications ProgrammingProgramming the ID Number Interrogating the ID Number Programming Dial-out Telephone Numbers Enter numberInterrogating a Dial-out Telephone Number Erasing a Telephone NumberPress ENTER. The Model 1104 will say Enter Pause Tone or Pulse DialingSpecial Dialing Keys Incorporating a Pause Pound #Asterisk CodeIncorporating a Pound # or Asterisk PressedPress any unassigned number key from 1 to 4 to represent Special Dialing to a Beeper or Pager Now press Pause once to activate a four second delay. This Programming Rings Until Answer Interrogating Rings Until AnswerTAD Enable/Disable Using the TAD FeatureNo TAD In Use Programming the Listen-in Time Interrogating the Listen-in Time Call Delay Programming the Call DelayInterrogating Call Delay Enable/Disable Local Voice Mute Local Voice MuteProgramming Voice Repetitions 10.2 Interrogating Voice RepetitionsModel 1104 will recite the number programmed Programming Intercall Time Interrogating Intercall Time SecondsProgramming Max Calls Interrogating Max Calls Setting the Clock Interrogating for the Current Time Locking the Keypad Unlocking the KeypadUsing the number keys, enter the digits for the code Sensaphone Model 1104 User’s Manual Alarm Programming Programming Input Configuration StatusVerifying Enabled/Disabled Input Status Verifying Input ConfigurationChanging Enabled/Disabled Input Status Programming Input Recognition Time Immediately follows the number recited for that inputInterrogating Input Recognition Time Recites the digits as they are pressedPress the corresponding input key 1 to Programming Temperature Limits for a Selected Input Disabling Alarm Response to High or Low Temperature Interrogating High and Low Temperature LimitsTemperature Calibration Programming Temperature Calibration Interrogating Temperature CalibrationObtaining Current Temperature Enabling/Disabling the AC Power Alarm Programming Power Failure Recognition Time Model 1104 will recite the digits as they are pressedInterrogating Power Failure Recognition Time Programming Sound Alarm Sensitivity Using the number keys, enter a value for sound sensitivityProgramming High Sound Alarm Recognition Time Interrogating Sound SensitivityChanging Enabled/Disabled High Sound Alarm Exit Delay Touch-Tone Acknowledgment Acknowledgment Status Report & Remote AccessLocal Acknowledgment Callback Acknowledgment Example Status Report, No Alarms Example Status Report, Existing Alarms Example Status Report, Disabled Inputs Battery ConditionReplace batteries, if below 7.2 Volts Remote Access by Touch-Tone TelephoneBattery Condition OK, if over 8.2 Volts Activating Status Report Sensaphone Model 1104 User’s Manual Alarm Detection, Dial-out and Acknowledgment OperationTemperature Valid AlarmCall Delay Alarm MessageAlarm Messages Intercall TimeVoice Repetitions Call ProgressLocal, On-site AcknowledgmentTouch-Tone Fast CodeHave a good day TAD EnabledNumber...the last number it dialed Example a Dial-out Telephone Call Appendix a Troubleshooting Problem SolutionCommunications / Dial-out CauseAppendix a Troubleshooting Communications / Dial-out Problem Cause Solution Temperature Monitoring Problem Cause Solution Sound Level Monitoring Problem Cause Solution Other Monitoring Problem Cause Solution101 Appendix a Troubleshooting Be sure to use alkaline batteries-do not Use rechargeable nicad batteriesAppendix B Weekly Testing Procedure 104 Appendix C Accessories Part Number Sensor / SwitchSensaphone Model 1104 User’s Manual 106 Service Department Appendix D Returning the Unit for RepairYear Limited Warranty