AT&T 9370 user manual Batteries, Battery Life, Charge the Handset Battery Pack

Page 45

9370_to make pdf_1ATT 6/12/00 2:07 PM Page 43

BATTERIES

Battery Life

Battery life depends on how far the handset is from the base, and other environmental conditions.

NOTE: For optimum battery performance, charge your handset on the base every night.

	Operation:	Approximate Battery Life:

IN USE	Near base unit	10 hours
(phone on)	Away from base unit	10 hours

NOT IN USE	Ringer on	15 days
	Ringer off	30 days

Charge the Handset Battery Pack

This battery should remain charged up to fifteen days with the Ringer on and up to 30 days with the Ringer off. A fully charged battery provides an average talk time of about ten hours.

The battery pack needs charging when:

•A new battery is installed in the handset.

•The phone beeps four times when you press P.

•The battery status symbol on the screen is only partly displayed.

•The phone does not respond when you press P.

Place the handset in the base either in the face-down or face-up position so the CHARGING light turns on. The battery pack is typically fully charged in six hours. For best results, the initial charge should be 12 hours.

You can keep the battery fully charged by returning the handset to the base after each use.

If you repeatedly get a low battery indicator, even after six hours of charging, the battery should be replaced.

43

Image 45

Contents Revised 6/12/00 Advanced American Telephones. All rights reserved Contents Page Before YOU Begin About Caller ID with Call WaitingAbout Home and Local Area Codes Before You Install InstallationInstall the handset battery Table/Desk and Wall InstallationConnect the telephone line cord Feature Setup Message Window Display for Feature SetupSoftkeys Dial Mode Telephone Feature SetupHandset Ringer Off / Battery Save Handset RingerProgram Home and Local Area Codes Caller ID Feature SetupCaller ID with Call Waiting Call List OptionsAnswering System Feature Setup Select Your Announcement Ring Select / Toll SaverAudible Message Alert Change Remote Access Code Priority Call SignalChange Priority Calling Code Record Your Announcement from the Base Review Feature SettingsSet the Clock Delete an AnnouncementTalking Caller ID Feature Setup Caller Specific Outgoing Announcement Feature SetupAnnouncements Outgoing Local Review ADD Enter Number Done Menu Call ID DIR Directory MEM ANS SYS Delete Done Telephone Operation Redial Temporary ToneMute Hold IntercomRecord a Phone Conversation Headset Jack Changing ChannelsAT the Base Speaker Base Ringer VolumeHandset Locator Page/IntercomStore a Number in Memory Telephone MEMORY/DIRECTORYStore a Pause in a Memory Number Store a Name with a Memory NumberReplace a Stored Number View Memory Numbers Store a Number and Name from Call HistoryEdit Memory Numbers Delete Memory NumbersPriority Ring Numbers Dial a Memory Number from the HandsetDial a Memory Number from the Base Answering System Operation Audible IndicatorsAbout Mailboxes Announcement Play/SilentCall Screening/Intercept Answering CallsAnnouncement Bypass Record a MemoFunction Button Listen To, Save & Delete MessagesCL ↔ AO Message Window DisplayConnect with the Answering System Call ScreeningFrom the Cordless Handset From a Touch Tone PhoneFunction Command Remote Access CommandsEnd remote access call Voice Help Menu Audible SignalsCall Waiting Incoming Call HistoryMemory Match Caller ID Operation Review Call HistoryDisplay Dial Delete a Specific Call Record Delete Call Records from Call HistoryDelete All Call Records Caller ID Display MessagesOperating Range Battery Life Charge the Handset Battery PackBatteries Batteries Replace the Handset Battery Pack If the phone does not work at all, check these items first Case of DifficultyIf you have no dial tone To re-initialize the handset and baseIf you hear noise or interference when using the phone If the phone does not ring when you receive a callIf the caller’s name or phone number is not displayed If speakerphone conversation sounds distorted If messages are incompleteIf you have difficulty hearing messages If your outgoing announcement isn’t clear If CL appears in the Message WindowIndex Index Answering System Remote CommandsRemote Command Press