AT&T 9370 user manual If speakerphone conversation sounds distorted, If messages are incomplete

Page 50

9370_to make pdf_1ATT 6/12/00 2:07 PM Page 48

IN CASE OF DIFFICULTY

If the caller’s name or phone number is not displayed during Call Waiting:

•You should call your service provider to confirm that you subscribe to a combined Caller ID with Call Waiting service.

•The screen may not display the call information if someone is on an extension phone.

•The Caller ID with Call Waiting feature is inactive during a power interruption.

•Make sure the battery is charged.

•Make sure Caller ID with Call Waiting is turned on (follow the instructions under “Caller ID Feature Setup” in the FEATURE SETUP section of this manual).

If speakerphone conversation sounds distorted:

After the phone is powered up, the speakerphone initializes for about 10–15 seconds the first time it is used. Conversation should be clear after this.

If messages are incomplete:

•If a caller leaves a very long message, part of it may be lost when the system disconnects the call after three minutes.

•If the caller pauses for more than seven seconds, the system stops recording and disconnects the call.

•If the system’s memory becomes full during a message, the system stops recording and disconnects the call.

If you have difficulty hearing messages:

Check the volume setting.

If the system does not answer after the correct number of rings:

•Make sure that the two-digit message window in the base is on. If it is off, press 0[ON/OFF].

•If Toll Saver is on, the number of rings changes to two when you have new messages waiting.

•In some cases, the system may be affected by the ringing system used by the local telephone company.

•If the memory is full or the system is off, the system answers after 10 rings.

48

Image 50

Contents Revised 6/12/00 Advanced American Telephones. All rights reserved Contents Page About Home and Local Area Codes Before YOU BeginAbout Caller ID with Call Waiting Installation Before You InstallTable/Desk and Wall Installation Install the handset batteryConnect the telephone line cord Softkeys Feature SetupMessage Window Display for Feature Setup Handset Ringer Off / Battery Save Telephone Feature SetupDial Mode Handset RingerCaller ID with Call Waiting Caller ID Feature SetupProgram Home and Local Area Codes Call List OptionsAnswering System Feature Setup Audible Message Alert Select Your AnnouncementRing Select / Toll Saver Change Priority Calling Code Change Remote Access CodePriority Call Signal Review Feature Settings Record Your Announcement from the BaseDelete an Announcement Set the ClockCaller Specific Outgoing Announcement Feature Setup Talking Caller ID Feature SetupAnnouncements Outgoing Local Review ADD Enter Number Done Menu Call ID DIR Directory MEM ANS SYS Delete Done Telephone Operation Mute RedialTemporary Tone Record a Phone Conversation HoldIntercom Changing Channels Headset JackSpeaker Base Ringer Volume AT the BasePage/Intercom Handset LocatorTelephone MEMORY/DIRECTORY Store a Number in MemoryReplace a Stored Number Store a Pause in a Memory NumberStore a Name with a Memory Number Store a Number and Name from Call History View Memory NumbersDelete Memory Numbers Edit Memory NumbersDial a Memory Number from the Base Priority Ring NumbersDial a Memory Number from the Handset About Mailboxes Audible IndicatorsAnswering System Operation Announcement Play/SilentAnnouncement Bypass Answering CallsCall Screening/Intercept Record a MemoListen To, Save & Delete Messages Function ButtonMessage Window Display CL ↔ AOFrom the Cordless Handset Call ScreeningConnect with the Answering System From a Touch Tone PhoneRemote Access Commands Function CommandEnd remote access call Audible Signals Voice Help MenuMemory Match Call WaitingIncoming Call History Display Dial Caller ID OperationReview Call History Delete Call Records from Call History Delete a Specific Call RecordCaller ID Display Messages Delete All Call RecordsOperating Range Batteries Battery LifeCharge the Handset Battery Pack Batteries Replace the Handset Battery Pack If you have no dial tone Case of DifficultyIf the phone does not work at all, check these items first To re-initialize the handset and baseIf the caller’s name or phone number is not displayed If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call If you have difficulty hearing messages If speakerphone conversation sounds distortedIf messages are incomplete If CL appears in the Message Window If your outgoing announcement isn’t clearIndex Index Remote Commands Answering SystemRemote Command Press