NEC SP5008A user manual WAN Setting, Dhcp

Page 11

WAN Setting

	Item	Description		Static IP	DHCP	PPPoE
	Connected mode	Select the connection method for
		the WAN port of the
		SP5008A/SP5018A/SP5058A, you
		can choose the following:		V	V	V
		z	Static IP
		z	DHCP
		z	PPPoE

	Current IP Address	Show current IP address		V	V	V

	DNS server mode	Select the DNS behavior, you can
		choose the following:
		z	Auto
		z	Manual
		“DNS auto” will retrieve the DNS		V	V	V
		information sent from the DHCP		V	V	V
		information sent from the DHCP
		server.
		“Manual” will look at the specified
		Primary and Secondary DNS
		address.

	Primary DNS	Specify the address of the Primary		V	V	V
	address	DNS.		V	V	V
	address	DNS.

	Secondary DNS	Specify the address of the		V	V	V
	address	Secondary DNS.		V	V	V
	address	Secondary DNS.

	WAN Link Speed	Select the connection speed for the
		WAN port of the
		SP5008A/SP5018A/SP5058A, you
		can choose the following:		V	V	V
		z	Auto
		z	100M
		z	10M

	HTTP port for WEB	Specify the port number for WEB
	management	management, the allowable range is		V	V	V
		80,1024~65535.

	IP address	Specify the IP address.		V

	Subnet mask	Specify the subnet mask.		V

10

Image 11

Contents IP Telephony Gateway Online Upgrade Startup Table of ContentWeb Administration IntroductionOperation SpecificationIntroduction Key FeaturesSP5018A LED IndicatorsPhysical Description SP5058AT1/P1-T4/P4 SP5008AT1-T8 L1-L8Startup Login into the SystemPage Network Configuration Dhcp WAN SettingStatic IP Enable/Disable this optionDhcp PPPoE Description LAN SettingDescription Pabx Connection General configurationPabx Mode SP5018A only SIP SettingFXO Dialing Prefix Primary FXS SIP settingsSIP Setting Display name PasswordAccount NumberSIP Advanced Setting Feature is for FXS only Make sure your proxy server or soft switchSupports the feature, if the proxy does not support It and you enable this feature, all IP outgoing callsPayload Type Setting Page Line Setting Reg Enable HotlineNo Answer Forward Time FXS only Line1~Line8 relevant data TypePage ToS Setting ToS RTP Qos SettingDifferentiated Services Code Point Setting Dscp Dscp SignalSpeed Dial Editor Speed Dial SettingSpeed Dial Speed Dial Editor In P2P application Peer to Peer callDtmf Caller ID End Symbol Caller ID SettingCaller ID Setting Line 1~Line Dtmf Caller ID Start SymbolDefault symbol is C CDR mode CDR Server address CDR Server port CDR SettingPage Syslog mode Syslog Server address Syslog Server port Syslog SettingPage System setting Advanced ConfigurationPage Page Ping ip to keep alive network Ping timersec Sntp Setting Bandwidth Required Codec SettingCodec Priority Codec Packet SizeVoice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Country Min. Digit CountDigit Manipulation FXO Dial Prefix Third Example Dial PlanDial Plan Editor Page Provision Server ManagementExport File Import File Save-Reload settingUpgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Displays the MAC address of the WAN port Network StatusApplication version Boot versionVersion Info Post versionRegister Proxy Port StatusPort Type Confirm new password PasswordCurrent password New passwordRebooting the system Enable the representative line Peer to Peer mode FXO to FXSConfiguration All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking