NEC SP5008A user manual SP5018A

Page 74

		z	Password protected for Admin access authority
	Networking	z	PPPoE Client, DHCP Client / Server, NAT, SNTP
		z	QoS: DiffServ / ToS
	Management	z	User interface: HTTP and Telnet
		z	Firmware upgrade via FTP/TFTP/HTTP/Telnet
		z	Auto Provisioning

	Environment	z	Operating Temperature: 0 – 45 degree C
		z	Storage Temperature: 0 – 55 degree C
		z	Operating Humidity: 10 to 85% (non-condensing)
		z	Storage Humidity: 10 to 95% (non-condensing)
	Power Supply	DC 12V, 3A
	Emission	CE
		FCC Part 15, Class B

	Model	SP5018A

	Standards	z	SIPv2 (RFC 3261): Primary and Secondary Proxy, Primary and
			Secondary Outbound Proxy
	Interface	z	1 x RJ-45 WAN port of 10/100M
		z	4 x RJ-45 LAN ports of 10/100M
		z	4 x RJ-11 FXS ports for connecting with phone set and fax machine
		z	4 x RJ-11 FXO ports for connecting with PSTN line or PABX’s extension
	Voice Processing	z	Codec: G.711a/mu-law, G.723.1 (6.3K), G.729, G.729.A
		z	VAD, CNG, and Silence Suppression
		z	Echo Cancellation (G.165 / G.168)
		z	Adaptive Jitter Buffer
		z	Packet Loss Compensation
		z	Adjustable volume level
		z	DTMF relay: In-band, RFC 2833, SIP Info
	Call Features	z	Caller ID Detection: FSK, DTMF, ETSI (before ringing, between ringing)
		z	Call hold
		z	Call transfer (blind & consultant)
		z	Call forward (Unconditional, No answer, Busy)
		z	MWI (Message Waiting Indication)
		z	FAX over IP: G.711 pass-through, T.38 Fax relay
		z	PSTN Lifeline: PSTN bypass if network or system fails
		z	Detection of disconnect tone, polarity reversal, and loop current drop (zero
			voltage) on FXO ports

73

Image 74

Contents IP Telephony Gateway Online Upgrade Introduction Table of ContentWeb Administration StartupSpecification OperationKey Features IntroductionSP5058A LED IndicatorsPhysical Description SP5018AL1-L8 SP5008AT1-T8 T1/P1-T4/P4Login into the System StartupPage Network Configuration WAN Setting DhcpEnable/Disable this option Static IPDhcp PPPoE LAN Setting DescriptionDescription SIP Setting General configurationPabx Mode SP5018A only Pabx ConnectionPrimary FXS SIP settings FXO Dialing PrefixSIP Setting Number PasswordAccount Display nameSIP Advanced Setting It and you enable this feature, all IP outgoing calls Make sure your proxy server or soft switchSupports the feature, if the proxy does not support Feature is for FXS onlyPayload Type Setting Page Line Setting Line1~Line8 relevant data Type Enable HotlineNo Answer Forward Time FXS only RegPage Dscp Signal Qos SettingDifferentiated Services Code Point Setting Dscp ToS Setting ToS RTPSpeed Dial Editor Speed Dial SettingSpeed Dial Peer to Peer call Speed Dial Editor In P2P applicationDtmf Caller ID Start Symbol Caller ID SettingCaller ID Setting Line 1~Line Dtmf Caller ID End SymbolDefault symbol is C CDR Setting CDR mode CDR Server address CDR Server portPage Syslog Setting Syslog mode Syslog Server address Syslog Server portPage Advanced Configuration System settingPage Page Ping ip to keep alive network Ping timersec Sntp Setting Codec Packet Size Codec SettingCodec Priority Bandwidth RequiredVoice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Min. Digit Count CountryDigit Manipulation FXO Dial Prefix Third Example Dial PlanDial Plan Editor Page Management Provision ServerSave-Reload setting Export File Import FileUpgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Network Status Displays the MAC address of the WAN portPost version Boot versionVersion Info Application versionRegister Proxy Port StatusPort Type New password PasswordCurrent password Confirm new passwordRebooting the system Enable the representative line Peer to Peer mode FXO to FXSConfiguration All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking