NEC SP5008A Unregister All, Early media Treatment, Support SIP Ping, IP Anonymous Caller ID

Page 22

 

Session Refresh Request message.

 

 

Unregister All

Send SIP unregister signaling message after the

 

SP5008A / SP5018A / SP5058A has been restarted

 

 

Early media Treatment

Use early media treatment SIP protocol, where SIP

 

invite messages will not include SDP.

 

 

Support SIP Ping

Special feature used with only Nortel’s SIP proxy.

 

 

IP Anonymous Caller ID

When this feature is Enabled, all IP outgoing calls’

 

Caller ID will not be displayed to the destination.(Please

 

make sure your proxy server or soft switch

 

supports the feature, if the proxy does not support

 

it and you enable this feature, all IP outgoing calls

 

will be dropped.)

 

When Disabled, all IP outgoing calls’ Caller ID will be

 

displayed to the destination.

 

 

Support Message Waiting Indication

You can Enable or Disable the MWI function.( This

(MWI)

feature is for FXS only)

 

 

SIP Message Resend Timer Base (sec)

Specify the resend time in seconds for each SIP request

 

message that has not received a response.

 

 

Max. Response Time for Invite

Specify the timeout period for SIP Invite messages.

(1~30sec)

For example, if the timeout period is 10 seconds, when

 

the SP5008A / SP5018A / SP5058A sends an Invite

 

message and does not receive a response within 10

 

seconds, it will cancel the call.

 

 

1.Press the “Apply” button (at the bottom) after you finish to save changes.

2.Press the “Reboot” button to apply the changes.

21

Image 22
Contents IP Telephony Gateway Online Upgrade Introduction Table of ContentWeb Administration StartupSpecification OperationKey Features IntroductionSP5058A LED IndicatorsPhysical Description SP5018AL1-L8 SP5008AT1-T8 T1/P1-T4/P4Login into the System StartupPage Network Configuration WAN Setting DhcpEnable/Disable this option Static IPDhcp PPPoE LAN Setting DescriptionDescription SIP Setting General configurationPabx Mode SP5018A only Pabx ConnectionPrimary FXS SIP settings FXO Dialing PrefixSIP Setting Number PasswordAccount Display nameSIP Advanced Setting It and you enable this feature, all IP outgoing calls Make sure your proxy server or soft switchSupports the feature, if the proxy does not support Feature is for FXS onlyPayload Type Setting Page Line Setting Line1~Line8 relevant data Type Enable HotlineNo Answer Forward Time FXS only RegPage Dscp Signal Qos SettingDifferentiated Services Code Point Setting Dscp ToS Setting ToS RTPSpeed Dial Speed Dial SettingSpeed Dial Editor Peer to Peer call Speed Dial Editor In P2P applicationDtmf Caller ID Start Symbol Caller ID SettingCaller ID Setting Line 1~Line Dtmf Caller ID End SymbolDefault symbol is C CDR Setting CDR mode CDR Server address CDR Server portPage Syslog Setting Syslog mode Syslog Server address Syslog Server portPage Advanced Configuration System settingPage Page Ping ip to keep alive network Ping timersec Sntp Setting Codec Packet Size Codec SettingCodec Priority Bandwidth RequiredVoice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Min. Digit Count CountryDigit Manipulation FXO Dial Prefix Dial Plan Editor Dial PlanThird Example Page Management Provision ServerSave-Reload setting Export File Import FileUpgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Network Status Displays the MAC address of the WAN portPost version Boot versionVersion Info Application versionPort Type Port StatusRegister Proxy New password PasswordCurrent password Confirm new passwordRebooting the system Configuration Peer to Peer mode FXO to FXSEnable the representative line All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking