NEC SP5008A user manual Tone Setting

Page 45

3.2.5 Tone Setting

Dial tone	Specify the pattern of the Dial tone, you can adjust the
	high frequency, low frequency, high level, low level, the
	On and Off time for tone 1 and 2.

Ringback tone (FXS only)	Specify the pattern of the Ringback tone, you can adjust
	the high frequency, low frequency, high level, low level,
	the On and Off time for tone 1 and 2.

Busy tone	Specify the pattern of the Busy tone, you can adjust the
	high frequency, low frequency, high level, low level, the
	On and Off time for tone 1 and 2.

Call-waiting (FXS only)	Specify the pattern of the call-waiting tone, you can
	adjust the high frequency, low frequency, high level, low
	level, the On and Off time for tone 1 and 2.

Voice-Notify (for FXS+PSTN only)	Specify the pattern of the Voice-Notify, you can adjust
	the high frequency, low frequency, high level, low level,
	the On and Off time for tone 1 and 2.

ROH Tone (FXS only)	Specify the pattern of the ROH Tone, you can adjust the
	high frequency, low frequency, high level, low level, the
	On and Off time for tone 1 and 2. The ROH tone is a
	single high frequency tone used to warn users that their
	phone is not placed on-hook (hang up) correctly.

Disconnect tone 1	Specify the pattern of the disconnect tone for disconnect
	tone 1 (first set), you can adjust the high frequency, low
	frequency, high level, low level, the On and Off time for
	tone 1 and 2.

44

Image 45

Contents IP Telephony Gateway Online Upgrade Web Administration Table of ContentIntroduction StartupOperation SpecificationIntroduction Key FeaturesPhysical Description LED IndicatorsSP5058A SP5018AT1-T8 SP5008AL1-L8 T1/P1-T4/P4Startup Login into the SystemPage Network Configuration Dhcp WAN SettingStatic IP Enable/Disable this optionDhcp PPPoE Description LAN SettingDescription Pabx Mode SP5018A only General configurationSIP Setting Pabx ConnectionFXO Dialing Prefix Primary FXS SIP settingsSIP Setting Account PasswordNumber Display nameSIP Advanced Setting Supports the feature, if the proxy does not support Make sure your proxy server or soft switchIt and you enable this feature, all IP outgoing calls Feature is for FXS onlyPayload Type Setting Page Line Setting No Answer Forward Time FXS only Enable HotlineLine1~Line8 relevant data Type RegPage Differentiated Services Code Point Setting Dscp Qos SettingDscp Signal ToS Setting ToS RTPSpeed Dial Setting Speed DialSpeed Dial Editor Speed Dial Editor In P2P application Peer to Peer callCaller ID Setting Line 1~Line Caller ID SettingDtmf Caller ID Start Symbol Dtmf Caller ID End SymbolDefault symbol is C CDR mode CDR Server address CDR Server port CDR SettingPage Syslog mode Syslog Server address Syslog Server port Syslog SettingPage System setting Advanced ConfigurationPage Page Ping ip to keep alive network Ping timersec Sntp Setting Codec Priority Codec SettingCodec Packet Size Bandwidth RequiredVoice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Country Min. Digit CountDigit Manipulation FXO Dial Prefix Dial Plan Dial Plan EditorThird Example Page Provision Server ManagementExport File Import File Save-Reload settingUpgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Displays the MAC address of the WAN port Network StatusVersion Info Boot versionPost version Application versionPort Status Port TypeRegister Proxy Current password PasswordNew password Confirm new passwordRebooting the system Peer to Peer mode FXO to FXS ConfigurationEnable the representative line All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking