NEC SP5008A user manual T1-T8, L1-L8, T1/P1-T4/P4, LAN1-4

Page 7

1*. SP5008A: FXS = T1 - T8

SP5018A: FXS = T1 - T4, FXO = L1 - L4

SP5058A: FXO = L1 - L8

SP5008A

SP5008A Rear Panel

SP5058A

SP5058A Rear Panel

SP5018A

SP5018A Rear Panel

---------------------------------------------------------------------------------------------------

RESET	Factory default button. Press and hold for 5 seconds to reset
T1-T8	The RJ-11	FXS port 1-8, connects analog phone sets, trunk line in PABX.
L1-L8	The RJ-11	FXO port 1-8, connect to PSTN
T1/P1-T4/P4	It is a pair of FXO and FXS connector. The different is that the when power off
	or application is crashed, the FXO and FXS will be connected together
	automatically for local surviving.
WAN	RJ-45 port of 10/100M for connecting to modem
LAN(1-4)	RJ-45 port of 10/100M for connecting to PC or hub/switch that connects PCs
DC 12V	The power socket, input AC 100V~120V; output DC12V.3A

---------------------------------------------------------------------------------------------------

6

Image 7

Contents IP Telephony Gateway Online Upgrade Startup Table of ContentWeb Administration IntroductionOperation SpecificationIntroduction Key FeaturesSP5018A LED IndicatorsPhysical Description SP5058AT1/P1-T4/P4 SP5008AT1-T8 L1-L8Startup Login into the SystemPage Network Configuration Dhcp WAN SettingStatic IP Enable/Disable this optionDhcp PPPoE Description LAN SettingDescription Pabx Connection General configurationPabx Mode SP5018A only SIP SettingFXO Dialing Prefix Primary FXS SIP settingsSIP Setting Display name PasswordAccount NumberSIP Advanced Setting Feature is for FXS only Make sure your proxy server or soft switchSupports the feature, if the proxy does not support It and you enable this feature, all IP outgoing callsPayload Type Setting Page Line Setting Reg Enable HotlineNo Answer Forward Time FXS only Line1~Line8 relevant data TypePage ToS Setting ToS RTP Qos SettingDifferentiated Services Code Point Setting Dscp Dscp SignalSpeed Dial Speed Dial SettingSpeed Dial Editor Speed Dial Editor In P2P application Peer to Peer callDtmf Caller ID End Symbol Caller ID SettingCaller ID Setting Line 1~Line Dtmf Caller ID Start SymbolDefault symbol is C CDR mode CDR Server address CDR Server port CDR SettingPage Syslog mode Syslog Server address Syslog Server port Syslog SettingPage System setting Advanced ConfigurationPage Page Ping ip to keep alive network Ping timersec Sntp Setting Bandwidth Required Codec SettingCodec Priority Codec Packet SizeVoice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Country Min. Digit CountDigit Manipulation FXO Dial Prefix Dial Plan Editor Dial PlanThird Example Page Provision Server ManagementExport File Import File Save-Reload settingUpgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Displays the MAC address of the WAN port Network StatusApplication version Boot versionVersion Info Post versionPort Type Port StatusRegister Proxy Confirm new password PasswordCurrent password New passwordRebooting the system Configuration Peer to Peer mode FXO to FXSEnable the representative line All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking