ClearSounds A1600 manual Installing Batteries, Charging the Handset

Page 19

Installing Batteries

Three AAA re-chargeable Ni-MH batteries come with your phone. You must install the handset batteries before using your phone.

1.Remove the battery compartment cover by sliding it downwards.

2.Insert the new batteries. Be sure to observe battery polarity as imprinted on the inside of the compartment.

3.Replace the battery compartment cover by sliding upward until it clicks into place

Note: The batteries need to be replaced if they do not recover their full storage capacity after recharging. Check the battery icon on the LCD to see the battery charge level.

When replacing the batteries, always use good quality Ni-MH AAA re-chargeable batteries.

Charging the Handset

1.Place the handset into the base. The LCD screen will light up and you will hear a beep to indicate charging has begun.

2.Important: Before initial operation, you should fully charge the handset for at least 15 hours.

3.After the batteries are fully charged, check for dial tone by pressing the dial key on the handset.

When battery power is very low and you place the handset on

the base, the display will show . Check the battery icon on the LCD to see the battery charge level.

19 – ENGLISH

Image 19
Contents Operating Manual Table of Contents Handset Operation Handset Settings Additional Handset Functions Prior to USE Important Safety InstructionsEnglish English Handset Please Save These Instructions Location of ControlsLeft Side of Handset English Back Side of Base End Key HandsetNavigation Key Base Call Waiting Key Volume Up/Down KeyVolume & Tone Keys Up/Down KeysBase Answering Machine Installation of Your ClearSounds A1600 Dect Battery top rightSignal top left Alarm top centerParts Checklist Charging the Handset Installing BatteriesMenu Navigation Setting UP Your Base SpeakerphoneUsing the Handset Carrying Clip Using your Phone with Hearing Aids and Cochlear ImplantsTo Exit from any Menu To Access a Menu OptionMain Menu Submenu LCD Display Language SettingSwitch to Smaller Font Contrast SettingDate Format Setting Hour Format SettingSet Date & Time LCD Descriptions Reviewing Voice Mail Messages Ringer Setting Phone Base SettingsAudible Ringer Visual Ringer & Shaker Option Keypad Tones SettingCall Waiting Flash Dialing Mode SettingAuto On Hook Talking Caller ID Setting Talking Dialing SettingTalking Review Function Caller ID, Phonebook & Redial Basic Phone Functions Using the Hands-Free Headset or Audio JackUsing the Base Amplification Function English Answering a Call Using your Base SpeakerphoneMaking a Call Dialing from Standby Mode One-Touch Memory Setting & DialingStoring Memory Numbers while the telephone is not in use Dialing from Memory Numbers Inserting Photos in Memory KeysErase Memory Numbers Dialing from the Redial List Mute SettingHold Function Redial FunctionUse Redial List Options Caller ID CID OperationStoring CID Records Receiving CID RecordsCaller ID on Call Waiting Deleting a Single Caller List Record Caller ID ListViewing the Caller List Dialing a Number from the Caller ListDeleting All Caller List Records Phonebook OperationStoring Caller List Records Clarification Adding Phonebook EntriesDialing a Number from the Phonebook Using a PauseUsing Phonebook Options Viewing Phonebook EntriesMenu Navigation Setting UP Your Cordless HandsetMain Menu Submenu DD-MM-YY MM-DD-YY Registering the Handset Handset SET UPDelete/Terminate Handset Handset NameBase Selection Handset ResetDialing Mode Out of Range AlarmCall Waiting Flash Contrast Settings LCD SettingsModify PIN Personal Identification Number Date & Time Format Settings Handset Settings Visual and Vibrating Ringer Auto Answer Setting Turning the Handset Power On/Off ModeLanguage Setting Talking Keypad Using the Auto Amplification Feature Using the Handset Amplification FunctionStandby mode Using your Handset SpeakerphoneDuring a call Cordless Handset in the base Answering a Call from the Cordless HandsetMaking a Call from the Cordless Handset Cordless Handset out of the baseCordless Handset Dialing from the Memory M1 M4 keysViewing, Editing or Deleting M1-M4 Memory Numbers Storing M1-M4 Memory NumbersDialing from M1-M4 Memory Numbers Dial from the Redial Book Redial Function HandsetCaller ID CID Operation Caller ID on Call Waiting Viewing the Caller List Method Deleting All Caller List Records Phonebook Operation Adding Phonebook Entries Editing name, number, ring tone PB Phonebook Status DeletingKey Lock AlarmAdditional Functions PagingTorch Turn On/Off Setting UP Your Answering MachineUsing the Base Using the HandsetRings to Answer TAM SettingsRecord Time Voice Prompt Language Announces answering machine functions Answer Mode SelectionRecording Outgoing Message English Play Announcement Screening Calls only the handset can intercept the call Restore Default AnnouncementsAnswering Machine Volume Message OptionsPlay Messages Delete Messages Record a Memo Message Playback SpeedSecurity ID/PIN Security ID/PIN & Remote AccessNothing appears on the display TroubleshootingRemote Access No dial toneVisual ringer and vibrating handset will not activate Handset seems to have a short battery lifeLow handset or speaker volume No audible ringerNo Caller ID information while on a call Noise, Static, Interference while using the phoneNo numbers dialed when memory button is pressed Caller ID information does not showTo learn more, call ClearSounds at Technical SpecificationsFCC Wants YOU to Know Service Requirements Industry Canada CS03 Statement Limited ONE-YEAR Warranty Service in United States and Canada, contact
Related manuals
Manual 1 pages 214 b