Panasonic KX-PRW130 operating instructions FCC RF Exposure Warning

Page 56

Useful Information

manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices.

WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:

1)Remain on the line and briefly explain to the dispatcher the reason for the call.

2)Perform such activities in the off-peak hours, such as early morning or late evenings.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this phone.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the cordless telephone further away from the TV or VCR. This will often reduce or eliminate interference.

FCC RF Exposure Warning:

L This product complies with FCC radiation exposure limits set forth for an uncontrolled environment.

L To comply with FCC RF exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all person’s body.

L This product may not be collocated or operated in conjunction with any other antenna or transmitter.

L For body-worn operation, the handset must be used only with a non-metallic accessory. Use of other accessories may not ensure compliance with FCC RF exposure requirements.

Notice:

L FCC ID can be found inside the battery compartment or on the bottom of the units.

56For assistance, please visit http://www.panasonic.com/help

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Premium Design Phone with Smartphone Connect Thank you for purchasing a Panasonic productTable of Contents Accessory information Supplied accessoriesAdditional/replacement accessories Other informationFeature/Model no Expanding your phone systemSmartphone Your smartphone 4 maxFor your safety Important safety instructions BatteryFor best performance Base unit location/avoiding noiseSpecifications Other informationEnvironment Routine careSimplified configuration WPS PBC Power source Power consumption Base unitEncryption Operating conditionsSetting up Battery installationConnections Base unitIntelligent eco mode Battery chargingDuring a power failure Battery levelControls Display iconsHandset Base unitLanguage settings Date and timeDisplay language Voice guidance languageOther settings Screen saver modeDialing mode Recording your greeting messageUseful features during a call Making callsAnswering calls HoldFor call waiting or Call Waiting Caller ID service users Temporary tone dialing for rotary/pulse service usersMute FlashIntercom Transferring calls, conference callsMaking an intercom call Answering an intercom callPhonebook Adding phonebook entriesCharacter table for entering names Erasing the character or numberGroups Finding and calling from a phonebook entryEditing entries Storing caller information to the phonebookSpeed dial Erasing entriesChain dial Adding phone numbers to speed dial keysErasing an entry Viewing an entry/Making a callDisplay the menu tree and direct command code table Menu listSettings Ring count*1 Rings Voice Mail accessMemo alarm Alarm1-5 Once Time adjustment *1, *3 Caller IDSettings Ring adjustments Ringer volumeSilent mode On/Off Silent mode 1100 PM/0600Voice mail Save VM access#*1 Speed dialDisplay VM tone detect*1 Wallpaper Wallpaper1Set tel line Set dial mode *1 Pulse Setting *1, *18 Country codeNetwork settings Current status Wi-Fi settings ConnectBattery check Ring adjustments*19Silent mode On/Off On/OffOnce AlarmOff Turning silent mode on/off Call blockChanging the start and end time Selecting groups to bypass silentSetting the first ring for the call block list Baby monitorStoring unwanted callers Blocking incoming calls without phone numberSetting the baby monitor To monitor from an outside lineTo monitor with a handset Turning off the baby monitorOther programming Answering the baby monitorChanging the handset name Calendar/ScheduleRegistering a unit Operating additional unitsRegistering a handset to the base unit Deregistering a handsetUsing Caller ID service Caller ID featuresCaller list Talking Caller IDCaller ID number auto edit feature Editing a caller’s phone numberErasing selected caller information Erasing all caller informationUsing a pre-recorded greeting message Answering systemGreeting message Memory capacity including your greeting messageUsing the base unit Using the handsetListening to messages Playing back the greeting messageMbN Edit & Call a MSelectN Operating the answering systemCalling back Caller ID subscribers only New message alert by a call Advanced new message alerting featuresAudible message alert Remote access code Using the answering system remotelyRemote operation Voice guidanceAnswering system settings Remote commandsTurning on the answering system remotely Call screeningCaller’s recording time Selecting Greeting onlySmartphone integration Network settingsTypical configuration Dhcp Simplified configuration WPS, Dhcp Advanced configuration static IP settingsMbN WPS Easy setting a MSelectN Smartphone Connect appOther network features Wi-Fi repeater modeConfirming your wireless router’s Wi-Fi signal strength Resetting the base unit’s network settingsVoice mail service Storing the voice mail VM access numberVoice mail VM tone detection Listening to voice mail messagesDisplay message Error messagesCause/solution Troubleshooting ProblemGeneral use Menu listBattery recharge Making/answering calls, intercomCaller ID/Talking Caller ID New Voice Mail is shown Answering systemVoice mail Liquid damage Network connection troubleshooting Cannot obtain IP Failed to connect is displayed Wrong password isIP address FCC and other information FCC RF Exposure Warning Guía Rápida Española ConexionesGuardar s OFF Idioma de la pantallaIdioma de la guía de voz Agregar Ent. Nueva s Selec Núm Teléfono 1 s SelecPreguntas frecuentes Pregunta Causa y soluciónYou may also contact us directly at Fax Only Customer servicesOr, send your request by E-mail to Warranty For United States and Puerto Rico Limited Warranty CoverageMail-In Service--Online Online Repair Request Parts Labor One 1 YearLimited Warranty Limits And Exclusions When you ship the productIndex Ringer Base unit Ringer Handset 14 Speaker Page Page Read troubleshooting page in the Operating Instructions For your future reference
Top Page Image Contents