Panasonic KX-TG1062M, KX-TG1063, KX-TG1061 Wall mounting, Belt clip, Charger, To attach

Page 40

Useful Information

Wall mounting

Base unit

1Connect the AC adaptor and telephone line cord. Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow.

L The word “UP” should face upward.

2Connect the telephone line cord. Mount the unit by inserting the mounting pins into the round openings on the adaptor (for pin 2, use the round cut out at the bottom of the adaptor if you are using the 4 inch phone plate), then slide the unit down to secure it. Connect the AC adaptor to power outlet (page 8).

L There are 2 common types of wall phone plates. The distance between 1 and 2 may vary depending on the size of the wall phone plate installed.

Charger

1Drive the screws (not supplied) into the wall.

25.4mm (1 inch)

Screws

(120 V AC, 60 Hz)

2Mount the charger (A), then slide it down (B) and to the right (C) until it is secure.

A

B

C

Belt clip

■ To attach

■ To remove

40

For assistance, please visit http://www.panasonic.com/help

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Operating Instructions Table of Contents Accessory information Supplied accessoriesModel composition Series Model No Base unit Handset QuantityAdditional/replacement accessories Accessory item Order numberExpanding your phone system Handset optional KX-TGA106For your safety Important safety instructions Other information Setting up Battery installationBattery charge ConnectionsDuring a power failure Battery level IconBase unit ControlsHandset Display Using the navigator key/volume key VOL., ?Soft keys Initial settings Dialing modeDisplay language Voice guidance languageMaking calls Answering calls Useful features during a callHold For call waiting or Call Waiting Caller ID service users Temporary tone dialing for rotary/pulse service usersMute FlashAdding entries Base unit/handset phonebookGroups Editing entries Finding and calling a phonebook entryErasing entries Making a call using a speed dial button Canceling a speed dial assignmentSpeed dial Chain dialCopying phonebook entries Copying an entryCopying all entries OFFProgrammable settings Programming by scrolling through the display menus= Base unit / YHandset Menu Base unit Main menu Sub-menuHandset Main menu Sub-menu Programming using the direct commands Operating Feature Setting System Unit CodeHandset*7 VM tone detect Alarm Silent modeSpecial programming Call block Caller ID subscribers only Registering a unit Operating additional unitsRegistering a handset to a base unit Additional handsetsUsing Caller ID service Caller ID featuresCaller list Group ringer tone for phonebookCaller ID number auto edit feature Editing a caller’s phone number before calling backExample Turning Caller ID auto edit on/off = Base unit / YHandsetErasing all caller information Erasing selected caller informationStoring caller information to the phonebook Turning the answering system on/off Answering systemGreeting message Listening to messages using the base unit Listening to messages using the handset Operating the answering systemMenu iPLAY To listen to new messagesRemote access code Using the answering system remotelyRemote commands Remote operationAnswering system settings Save iOFF For voice mail service subscribersTurning on the answering system remotely Number of rings before the unit answers a callMessage alert Turning the call screening on/offVoice mail service Voice mail message indicationVoice mail VM tone detection Turning VM tone detection on/offIntercom Handset locatorTransferring calls, conference calls Making an intercom callTo transfer the call To establish a conference call Press ConfTo transfer the call Press OFF Answering a transferred call = Base unitWall mounting Belt clipCharger To attachError messages Display message Cause/solutionTroubleshooting General use Problem Cause/solutionProgrammable settings Problem Cause/solution Battery recharge Problem Cause/solutionProblem Cause/solution Caller ID Problem Cause/solutionAnswering system Problem Cause/solution Liquid damage Problem Cause/solution FCC and other information FCC RF Exposure Warning Guía Rápida Española InstalaciónIdioma de la guía de voz Auricular predeterminado inglés Operaciones básicas Para grabar su propio mensaje Mensaje marcador Preguntas frecuentes Solución rápida de problemas 1El auricular inalámbrico muestra2El auricular no emite ningún tono de marcación Reconecte Reconecte Adaptador HablarCómo registrar un auricular en la unidad base Customer services Customer Services Directory United States and Puerto RicoWarranty For United States and Puerto Rico Ship-In ServiceOne Panasonic Way, Secaucus, New Jersey Parts Labor One 1 YearLimited Warranty Limits And Exclusions Index Read these Operating Instructions Call us at 1-800-211-PANAFor your future reference Copyright
Top Page Image Contents