Panasonic KX-TG8162AL One touch eco mode, Display mode, Using the smart function key Top Key

Page 15

Getting Started

Using the smart function key (Top Key)

When the smart function indicator flashes rapidly/slowly, press MSmart functionN.

RThe above features can be activated depending the situation.

RIf you answer a call using the smart function key, the speakerphone is activated.

REven if the handset is placed on the base unit or charger, the feature can be activated. You can talk or listen to new messages without lifting up the handset. If you want to perform further operations, lift up the handset.

RWhen the unit has new messages and missed calls, the unit can be operated to play the new messages first and then show the missed calls.

Note:

RWhile key lock is on (page 18), incoming calls can be answered, but the following features are disabled even when the smart function indicator flashes slowly.

Listen to new messages. (page 39)

View the caller list when there are missed calls. (page 35)

Setting the smart function key (Top Key Setup)

The Top key setup for the following features must be “On”.

New Message(Default: On)

Missed Call(Default: Off)

The settings can be set for each handset.

1 (middle soft key) #278

2MbN: Select the desired setting and press

.

R “” is displayed next to the selected features.

R To cancel a selected feature, press

again. “” disappears.

3 a MN

Note:

RIf the smart function indicator flashes when the handset is not placed on the base unit

or charger, battery consumption is faster than usual.

One touch eco mode

The MR/ECON button on the handset enables you to activate the eco function with one touch. By activating eco mode, your unit can reduce the base unit transmission power by up to

90 % in standby mode.

You can turn on/off one touch eco mode by just pressing MR/ECON. The default setting is Normal.

When the one touch eco mode is on: Low

is temporarily displayed and is shown on the handset display instead of .

When the one touch eco mode is off: Normalis temporarily displayed and goes off from the handset display.

Note:

RWhen there is another cordless phone nearby and it is in use, the base unit transmission power may not be reduced.

RActivating one touch eco mode reduces the range of the base unit in standby mode.

RIf you set the repeater mode to On(page 33):

One touch eco mode is cancelled.

Eco Setupis not shown in the display menu (page 27).

Display mode

You can select to display either a single item or multiple items on one screen at a time for the following features:

handset main menu icons in function menu

menu list, recorded message list, phonebook list, caller list, and redial list

Select the desired setting:

Multi Items: Multiple entries/all menu icons are shown on one screen at a time.

Single Item: An entry/a menu icon is

shown on one screen in large characters at a time.

The default setting is Multi Items.

15

Image 15
Contents Thank you for purchasing a Panasonic product Digital Cordless Answering SystemTable of Contents Accessory information Supplied accessoriesModel composition Model number Additional/replacement accessoriesAccessory item Expanding your phone systemFor your safety Ni-MH batteries AAA R03 size Important safety instructionsBattery General noticesSpecifications For best performanceOther information Operating conditions RF transmission powerFrequency range ChargerConnections Setting upBattery installation Battery chargingBattery level Icon Battery levelOperation Operating time Controls HandsetBase unit Line DisplayHandset display items Greeting Only isHandset main menu icons Screen saver modeBase unit display items Handset soft key iconsDisplay language Turning the power on/offInitial settings Smart function key Top KeySetting the smart function key Top Key Setup One touch eco modeDisplay mode Using the smart function key Top KeyUsing soft key Temporarily switching the display mode Programming the display mode beforehandAnswering calls Making callsKey lock Useful features during a callPower back-up operation Making calls during a power failureWhen only 1 handset is registered Continuing a call during a power failure Finding and calling from a phonebook entry Handset phonebookAdding entries CategoriesSpeed dial Copying phonebook entriesEditing entries Erasing entriesCopying all entries Copying an entryDisplay the menu tree and direct command code table Programmable settingsRings Auto Recording Time *1 Minute Settings Number of Rings *1 2-9 RingsDisplay Mode Colour2 Multi Items Ringer Volume HandsetTime Adjustment *1, *8 Caller ID Night Mode On/OffRing Delay 30 sec Memo Alarm Alarm1-5 OnceTime Adjustment*1, *8 Caller ID Time Settings Set Date/Time *1Memo Alarm Once Alarm1-5 Daily WeeklyRegister Register H.set Power Failure Cancel Register*2Base Unit PIN*1 0000 Repeater Mode*1Off AlarmNight mode Special programmingIncoming call barring Caller ID subscribers only Changing the handset nameViewing/editing/erasing bar call numbers Setting call restrictionStoring an area code to be deleted automatically Storing unwanted callersRegistering a handset to the base unit Registering a unitChanging the base unit PIN Personal Identification Number Operating additional unitsDect repeater Setting the repeater modeCategory ringer tone Using Caller ID serviceCaller ID features Call waiting and Caller ID compatibleCaller list To store the name, continue from , Adding entries, Call screening Answering systemGreeting message Memory capacity including your greeting messageListening to messages using the handset Listening to messages using the base unitMbN Call Back a Listening to messages from the message listOperating the answering system Calling back Caller ID subscribers onlyRemote operation Remote access codeUsing the answering system remotely Remote commandsNumber of rings before the unit answers a call Answering system settingsFor service provider voice mail subscribers Turning on the answering system remotelyAnswering System Voice mail service Intercom Handset locatorTransferring calls, conference calls Character entry modes Character entryExtended 1 character table Extended 2 character tableCyrillic character table Error messages Cause/solutionDisplay message Troubleshooting ProblemGeneral use Programmable settings Battery rechargeMaking/answering calls, intercom Answering system Caller IDBelt clip Liquid damageTo attach Wall mounting template Wall mountingIndex Page Page For your future reference Attach your purchase receipt hereSales Department