Panasonic KX-TG8163AL, KX-TG8162AL Registering a unit, Operating additional units

Page 32

Programming

Changing the base unit PIN (Personal Identification Number)

Important:

RIf you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, contact an authorised service centre.

1 (middle soft key) #132

2Enter the current 4-digit base unit PIN (default: “0000”).

3Enter the new 4-digit base unit PIN. a

a M N

Registering a unit

Operating additional units

Additional handsets

Up to 6 handsets can be registered to the base unit.

Important:

RThe additional handset model recommended for use with this unit is noted on page 4. If another handset model is used, certain operations (handset settings, base unit settings, etc.) may not be available.

Registering a handset to the base unit

The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, is displayed even when the handset is near the base unit), re-register the handset.

1Handset:

(middle soft key) #130

2Base unit:

Press and hold MN for about 5 seconds, until the registration tone sounds.

RIf all registered handsets start ringing, press MN again to stop, then repeat this step.

RThe next step must be completed within 90 seconds.

3Handset:

a Wait until “Base PIN” is displayed. a Enter the base unit PIN

(default: “0000”). a

R If you forget your PIN, contact an authorised service centre.

R When the handset has been registered

successfully, is displayed.

Note:

R While registering, “Base in registering” is displayed on all registered handsets.

RWhen you purchase an additional handset, refer to the additional handset’s installation manual for registration.

Deregistering a handset

A handset can cancel its own registration to the base unit, or other handsets registered to the same base unit. This allows the handset to end its wireless connection with the system.

1 (middle soft key) #131

R All handsets registered to the base unit are displayed.

2MbN: Select the handset you want to cancel. a

3MbN: “Yes” a

R A confirmation tone sounds.

R The handset does not beep when cancelling its own registration.

4MN

Increasing the range of the base unit

You can increase the signal range of the base unit by using a DECT repeater. Please use only the Panasonic DECT repeater noted on page 4. Contact your Panasonic dealer for details.

32

Image 32

Contents Digital Cordless Answering System Thank you for purchasing a Panasonic productTable of Contents Model composition Accessory informationSupplied accessories Additional/replacement accessories Accessory itemExpanding your phone system Model numberFor your safety Important safety instructions BatteryGeneral notices Ni-MH batteries AAA R03 sizeOther information SpecificationsFor best performance RF transmission power Frequency rangeCharger Operating conditionsSetting up Battery installationBattery charging ConnectionsOperation Operating time Battery levelIcon Battery level Base unit ControlsHandset Display Handset display itemsGreeting Only is LineScreen saver mode Base unit display itemsHandset soft key icons Handset main menu iconsTurning the power on/off Initial settingsSmart function key Top Key Display languageOne touch eco mode Display modeUsing the smart function key Top Key Setting the smart function key Top Key SetupProgramming the display mode beforehand Using soft key Temporarily switching the display modeMaking calls Answering callsUseful features during a call Key lockWhen only 1 handset is registered Power back-up operationMaking calls during a power failure Continuing a call during a power failure Handset phonebook Adding entriesCategories Finding and calling from a phonebook entryCopying phonebook entries Editing entriesErasing entries Speed dialCopying an entry Copying all entriesProgrammable settings Display the menu tree and direct command code tableSettings Number of Rings *1 2-9 Rings Display Mode Colour2 Multi ItemsRinger Volume Handset Rings Auto Recording Time *1 MinuteNight Mode On/Off Ring Delay 30 secMemo Alarm Alarm1-5 Once Time Adjustment *1, *8 Caller IDTime Settings Set Date/Time *1 Memo Alarm OnceAlarm1-5 Daily Weekly Time Adjustment*1, *8 Caller IDPower Failure Cancel Register*2 Base Unit PIN*1 0000Repeater Mode*1 Register Register H.setAlarm Night modeSpecial programming OffChanging the handset name Incoming call barring Caller ID subscribers onlySetting call restriction Storing an area code to be deleted automaticallyStoring unwanted callers Viewing/editing/erasing bar call numbersRegistering a unit Changing the base unit PIN Personal Identification NumberOperating additional units Registering a handset to the base unitSetting the repeater mode Dect repeaterUsing Caller ID service Caller ID featuresCall waiting and Caller ID compatible Category ringer toneCaller list To store the name, continue from , Adding entries, Answering system Greeting messageMemory capacity including your greeting message Call screeningListening to messages using the base unit Listening to messages using the handsetListening to messages from the message list Operating the answering systemCalling back Caller ID subscribers only MbN Call Back aRemote access code Using the answering system remotelyRemote commands Remote operationAnswering system settings For service provider voice mail subscribersTurning on the answering system remotely Number of rings before the unit answers a callAnswering System Voice mail service Transferring calls, conference calls IntercomHandset locator Character entry Character entry modesCyrillic character table Extended 1 character tableExtended 2 character table Display message Error messagesCause/solution General use TroubleshootingProblem Making/answering calls, intercom Programmable settingsBattery recharge Caller ID Answering systemTo attach Belt clipLiquid damage Wall mounting Wall mounting templateIndex Page Page Sales Department For your future referenceAttach your purchase receipt here