JVC MX-WMD90 manual Reinforcing the Bass Sound, Activating the Surround Effect

Page 15

Reinforcing the Bass Sound

The richness and fullness of the bass sound is maintained regardless of how low you set the volume.

You can use this effect only for playback.

To get the effect, press ACTIVE BASS EX. (extension) so that the ACTIVE BASS EX. lamp lights up on the unit.

(in the main display)

To cancel the effect, press the button again so that the lamp goes off. “OFF” also appears in the main display.

Activating the Surround Effect

You can obtain a “being-there” feeling while listening to any source.

You can use this effect only for playback.

To get the effect, press SURROUND so that the SURROUND lamp lights up on the unit.

•Each time you press the button, the surround effect changes as follows:

NORMAL WIDE SUPER WIDE

OFF

(Canceled)

The surround effect increases as you select —:

NORMAL =WIDE =SUPER WIDE

To cancel the effect, press the button repeatedly until the SURROUND lamp goes off. “OFF” also appears in the main display.

Selecting the Sound Modes

You can select one of the 5 preset sound modes. You can use the sound mode only for playback.

To select the sound modes, press SOUND repeatedly so that the SOUND lamp lights up on the unit.

• Each time you press the button, the sound modes change

as follows:

 

 

 

 

 

 

 

 

 

 

 

ROCK

 

 

 

VOCAL

 

CLASSIC

 

 

POP

 

 

 

 

 

 

 

 

 

FLAT

 

 

MANUAL=SET?

 

BGM

 

 

 

 

 

 

 

 

 

 

(Canceled)

 

 

 

 

 

 

 

 

 

 

ROCK: Good for rock’n’roll.

VOCAL: Good for vocal music.

CLASSIC: Good for classical music.

POP: Enhances middle frequency.

BGM: Good for easy-listening.

MANUAL = SET?: Your individual mode stored in memory. See “Creating Your Own Sound Mode — MANUAL Mode.”

FLAT: Cancels the sound mode.

Creating Your Own Sound Mode — MANUAL Mode

You can create and store your own sound mode only by using the buttons and controls on the unit.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the unit ONLY:

1 Press SOUND repeatedly until “MANUAL =SET?” appears in the main display.

2 Press SET.

Adjustable frequency range

3 Adjust the equalizer pattern.

1)Rotate the left jog dial to select the frequency range to adjust (LOW, MIDDLE, HIGH).

2)Rotate the right jog dial to adjust the level (–3 to +3) of the selected frequency range.

3)Repeat steps 1) and 2) to adjust the level of the other frequency ranges.

4 Press SET again (or wait until the above indication disappears).

The equalizer pattern you have created is stored in memory.

To use your own sound mode

Select “MANUAL = SET?” when using the sound modes. See “Selecting the Sound Modes.”

English

– 12 –

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MX-WMD90 Mises en garde, précautions et indications diverses Face For Canada/pour le CanadaIntroduction PrecautionsContents Become familiar with the buttons and controls on your unit Location of the Buttons and ControlsFront Panel Display WindowMD deck B section Front PanelAmplifier/tuner section MD deck a sectionRemote Control Remote ControlUnpacking Putting the Batteries into the Remote ControlConnecting Antennas Getting StartedTo connect an outdoor AM antenna Connecting SpeakersYou can connect the speakers using the speaker cords AM antennaTo connect a cassette deck Connecting Other EquipmentPress Demo Output terminalTo start the display demonstration manually Equipment FinallyBasic and Common Operations Front panel Remote controlTo adjust the clock again Setting the ClockTurning On the Power and Selecting the Sources Adjusting the VolumeActivating the Surround Effect Creating Your Own Sound Mode Manual ModeTo use your own sound mode Reinforcing the Bass SoundListening to FM and AM Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Tuning in a Preset StationPlaying Back CDs To exchange CDs during playback of another Loading CDsPlaying Back the Entire Discs Continuous Play Basic CD OperationsTo go to another track To go to another track directly using the number buttonsTo check the program contents Programming the Playing Order of the Tracks Program PlayTracks of all loaded CDs will play at random Playing at Random Random PlayRepeating Tracks or CDs Repeat Play Prohibiting Disc Ejection Disc LockPlaying Back MDs Playing Back the Entire MD Continuous Play When using MD deck aWhen using MD deck B Loading MDsBasic MD Operations To change the display IndicationsWhile playing an MD, you can do the following operations Programming the Playing Order Tracks Program PlayInsert an MD Insert MDs Press #/ 8 on MD deck B or MD B 6 on the remote controlRepeating Tracks Repeat Play To prohibit disc ejection Disc LockTracks of the loaded MDs will play at random FM/AM Tape AUX Recording on MDsRecording is only possible on MD deck B Before You Start RecordingAbout the track marks To avoid erasing important recordingsPress AUX again When recording from the cassette deck, start playing a tapeRecording the External AUX Equipment AUX Recording To check the remaining timeStart playing the source on the external equipment Various Recording FunctionsSynchronized Recording MD to MD Synchronized RecordingOn the unit only Load a CD To confirm the recording contentsCD to MD Synchronized Recording Press Start EnterRotate the left jog dial to select the recordable MD Single Track RecordingFirst Track Recording On the unit only Load CDsTo stop any time during editing process and start Listening Edit RecordingOn the unit only Prepare a CD or an MD as the source sound Repeat to program other tracksTriple Recording Prepare the source you want to record from Long RecordingEditing MDs Introducing MD Editing Functions Divide Function Press MD EditTo join the divided tracks again, see the Join function Rotate the right jog dial until Move ? appears Press SET Join FunctionMove Function To divide the joined tracks, see the Divide functionMD deck B starts playing the MD CANCEL, then select the correct track number againErase Function EditALL Erase Function Assigning Titles to MDs Assigning a Title Using the Unit Make sure that the character you want to change is flashing Changing the TitlePress Enter Start to finish the current title entry You can make a correction or change the titlePress Enter to finish the current title entry Track title entry indication mode appears whenPress MD Title Input Press the button for the next character you want to inputYou can assign titles during play or recording PO WER Using the TimersTo turn on the Recording Timer, press SET Using Recording TimerHow Recording Timer actually works To turn on or off Recording Timer after its setting is doneUnit is turned off Using Daily TimerHow Daily Timer actually works Volume level will be set the previous level whenTimer Priority Using Sleep TimerHow Sleep Timer actually works Handling CDs MaintenanceTo clean the CD General NotesAtrac Adaptive TRansform Acoustic Coding Utoc User Table Of ContentsAdditional Information MD Disc TypesMD limitations Sound Skip Guard MemorySymptom Possible Cause Action TroubleshootingMD Messages Signification SolutionSpecifications EN, FR JVC 0199KSMMDWJEM
Top Page Image Contents