JVC MX-WMD90 manual Introduction, Precautions

Page 4

English

Introduction

We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.

About This Manual

This manual is organized as follows:

•The manual mainly explains operations using the buttons and controls on the unit. You can also use the buttons on the remote control if they have the same or similar names (or marks) as those on the unit.

If operation using the remote control is different from that using the unit, it is then explained.

•Basic and common information that is the same for many functions is grouped in one place, and is not repeated in each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Basic and Common Operations” on pages 10 – 12.

•The following marks are used in this manual:

Gives you warnings and cautions to prevent from a damage or risk of fire/electric shock.

Also gives you information which is not good for obtaining the best possible performance from the unit.

Gives you information and hints you had better know.

Precautions

Power sources

•When unplugging from the wall outlet, always pull the plug, not the AC power cord.

DO NOT handle the AC power cord with wet hands.

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

•After starting heating in the room

•In a damp room

•If the unit is brought directly from a cold to a warm

place

Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again.

Others

•Should any metallic object or liquid fall into the unit, unplug the unit and consult your dealer before operating any further.

•If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet.

DO NOT disassemble the unit since there are no user serviceable parts inside.

If anything goes wrong, unplug the AC power cord and consult your dealer.

Installation

•Install in a place which is level, dry and neither too hot nor too cold — between 5˚C (41˚F) and 35˚C (95˚F).

•Install the unit in a location with adequate ventilation to prevent internal heat built-up in the unit.

•Leave sufficient distance between the unit and the TV.

•Keep the speakers away from the TV to avoid interference with TV.

DO NOT install the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.

– 1 –

Page 3 Page 5
Image 4
Page 3 Page 5
Contents MX-WMD90 Mises en garde, précautions et indications diverses For Canada/pour le Canada FacePrecautions IntroductionContents Location of the Buttons and Controls Front PanelDisplay Window Become familiar with the buttons and controls on your unitFront Panel Amplifier/tuner sectionMD deck a section MD deck B sectionRemote Control Remote ControlPutting the Batteries into the Remote Control Connecting AntennasGetting Started UnpackingConnecting Speakers You can connect the speakers using the speaker cordsAM antenna To connect an outdoor AM antennaConnecting Other Equipment To connect a cassette deckOutput terminal To start the display demonstration manuallyEquipment Finally Press DemoFront panel Remote control Basic and Common OperationsSetting the Clock Turning On the Power and Selecting the SourcesAdjusting the Volume To adjust the clock againCreating Your Own Sound Mode Manual Mode To use your own sound modeReinforcing the Bass Sound Activating the Surround EffectListening to FM and AM Broadcasts Tuning in a Station Presetting StationsTuning in a Preset Station To change the FM reception modePlaying Back CDs Loading CDs Playing Back the Entire Discs Continuous PlayBasic CD Operations To exchange CDs during playback of anotherTo go to another track directly using the number buttons To check the program contentsProgramming the Playing Order of the Tracks Program Play To go to another trackPlaying at Random Random Play Repeating Tracks or CDs Repeat PlayProhibiting Disc Ejection Disc Lock Tracks of all loaded CDs will play at randomPlaying Back MDs When using MD deck a When using MD deck BLoading MDs Playing Back the Entire MD Continuous PlayTo change the display Indications Basic MD OperationsWhile playing an MD, you can do the following operations Tracks Program Play Programming the Playing OrderInsert an MD Press #/ 8 on MD deck B or MD B 6 on the remote control Insert MDsTo prohibit disc ejection Disc Lock Repeating Tracks Repeat PlayTracks of the loaded MDs will play at random Recording on MDs FM/AM Tape AUXBefore You Start Recording About the track marksTo avoid erasing important recordings Recording is only possible on MD deck BWhen recording from the cassette deck, start playing a tape Recording the External AUX Equipment AUX RecordingTo check the remaining time Press AUX againVarious Recording Functions Synchronized RecordingMD to MD Synchronized Recording Start playing the source on the external equipmentTo confirm the recording contents CD to MD Synchronized RecordingPress Start Enter On the unit only Load a CDSingle Track Recording First Track RecordingOn the unit only Load CDs Rotate the left jog dial to select the recordable MDListening Edit Recording On the unit only Prepare a CD or an MD as the source soundRepeat to program other tracks To stop any time during editing process and startTriple Recording Long Recording Prepare the source you want to record fromEditing MDs Introducing MD Editing Functions Press MD Edit Divide FunctionTo join the divided tracks again, see the Join function Join Function Move FunctionTo divide the joined tracks, see the Divide function Rotate the right jog dial until Move ? appears Press SETCANCEL, then select the correct track number again Erase FunctionEdit MD deck B starts playing the MDALL Erase Function Assigning Titles to MDs Assigning a Title Using the Unit Changing the Title Press Enter Start to finish the current title entryYou can make a correction or change the title Make sure that the character you want to change is flashingTrack title entry indication mode appears when Press MD Title InputPress the button for the next character you want to input Press Enter to finish the current title entryYou can assign titles during play or recording Using the Timers PO WERUsing Recording Timer How Recording Timer actually worksTo turn on or off Recording Timer after its setting is done To turn on the Recording Timer, press SETUsing Daily Timer How Daily Timer actually worksVolume level will be set the previous level when Unit is turned offUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance To clean the CDGeneral Notes Handling CDsUtoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic CodingSound Skip Guard Memory MD limitationsTroubleshooting Symptom Possible Cause ActionSignification Solution MD MessagesSpecifications EN, FR JVC 0199KSMMDWJEM
Top Page Image Contents