Friedrich SH14, SH20 installation manual Figure O Typical Installation

Page 16

STEP 3. Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the inside wall surface (See Figure O).

STEP 4. Drill three (3) 5/32" dia. pilot holes through holes in sill-plate into the framing and install three (3) #12 x 2" long screws (Item #4) (See Figure O).

FIGURE O TYPICAL INSTALLATION

Trim moulding

Caulk all sides air tight

 

3/8" (10 mm) slope down

 

Note: Support brackets may be omitted from

Screw #12A x 2" long

through-the-wall installations if the cabinet is

secured as follows. Drill 2 holes in each side

Use 3.

and install 4 fasteners (2 each side).

 

 

Use #12A x 2" (51 mm) screws, toggle bolts or

 

expansion anchor bolts as shown in Step 5.

Sill plate

Guide channel

 

Support brackets (Item 1) (See note above)

Inside wall

Screw #12 x 2" long, use one in each bracket.

Surface

Drill 5/23 (4 mm) dia. pilot holes.

NOTE: ALTERNATE FASTENERS WHICH MAY BE USED FOR SECURING THE SILL PLATE IN THE WALL, AND THE SUPPORT BRACKETS TO THE OUTSIDE WALL ARE NOT FURNISHED, BUT ARE AVAILABLE AT A LOCAL HARDWARE STORE.

MOLLY OR TOGGLE BOLT

EXPANSION ANCHOR BOLT

STEP 5. Drill two (2) 5/32" (4 mm) dia. pilot holes in each side at the locations shown (Figure O) and install four (4) #12 x 2" screws (Item #4). If the hole construction in Step 2 provides a sturdy mount with solid vertical studs, no support brackets are required. The installation must support the weight of the unit plus an additional weight of 400 pounds (185 kg) on the rear of the cabinet. The support brackets may be used for through-the-wall installations as shown in Figure O, for additional support.

STEP 6. If desired, trim around the cabinet on the room side with a suitable frame molding furnished by the installer (See Figure O).

Page 16

Image 16
Contents USE, CARE, Installation Manual Table of Contents Page Part 3 Maintenance Checklist Part 2 Filter InformationHazardgard Unit Special Features Part 4 Hazardgard Special FeaturesTemperature Control Part 5 Control Panel Function Control PowerPart 6 Exclusive Installation Instructions Section I Electrical RequirementsHazardgard Window Mount Installation Hardware Accessory DetailSection Chassis Wiring and PreparationUnpacking the Unit Shell Cabinet Preparation BeforeSection V Shell Installation Sash Window InstallationsTypical Installation Sill Plate Slope downSection a a Section B BTHROUGH-THE-WALL Installations Wall PreparationFigure L Frame Wall Construction Figure O Typical Installation Chassis Installation Figure PFigure Q Friedrich Hazardgard Room AIR Conditioners Limited Warranty Page Manual DE USO Instalación Y Mantenimiento Instrucciones Para USO Y Mantenimiento Instrucciones Para LA InstalacionParte SeccionPage Parte 2 Informacion Sobre EL Filtro Parte 3 Lista DE Control Para EL MantenimientoParte 4 Caracteristicas Especiales DEL Hazardgard Parte 5 Panel DE Control Parte 6 ¡EXCLUSIVAInstrucciones Para Instalacion Seccion 1 Requerimientos ElectricosLista DE Accesorios Número Descripción Cantidad De itemDesempaque DE LA Unidad SeccionPreparacion Y Instalacion Electrica DEL Chasis Preparacion DEL Armazon Gabinete AntesSeccion V Instalacion DEL Armazon Instalaciones EN Ventanas DE BastidorInstalacion Tipica DEL Filo DEL Antepecho PasoFigura G Seccion V Instalacion DE LA Armazon Instalaciones a Traves DE LA ParedConstruccion Para Paredes MAS Gruesas Requisitos DE Tamaño DE LOS HuecosFigura L Construccion EN EL Marco DE LA Pared Construccion EN Paredes DE LadrilloFigura O Instalacion Tipica Instalacion DEL Chasis De la cubierta en la caja de empalme de conexiónFigura Q Friedrich AIR Conditioning CO. INC Page Manuel ’UTILISATION Instructions D’INSTALLATION Instructions D’UTILISATION ET D’ENTRETIENChapitre GarantieNettoyer le filtre fréquemment consulter lentretien général Chapitre 2 Renseignements SUR LE Filtre Chapitre 3 DépannagePage Commande DE Température Chapitre 6 ExclusivitéInstructions D’INSTALLATION Section I Alimentation ÉlectriqueDétail DES Accessoires Référence N Déballage DE L’APPAREIL Branchement DU Châssis ET PréparationPréparation DE L’ENVELOPPE Avanta P R È SSection V Installation DE L’ENVELOPPE Installation Dans UNE Fenêtre À GuillotineInstallation Typique DE LA Plaque DE Seuil Coupe a a Installation À Travers UN MUR Section V Installation DE LenveloppeDimensions Finies DE L’OUVERTURE Figure L Construction Avec UN Cadre EN Bois Figure O Installation Typique Installation DU Châssis ÉtapeDétail Garantie Limite DUN AN Climatiseurs Hazardgard Friedrich
Related manuals
Manual 56 pages 18.6 Kb

SH14, SH20 specifications

The Friedrich SH15 and SH20 models are exemplary representatives of advanced heating solutions, designed to address the diverse needs in residential and commercial environments. Engineered with a focus on efficiency, performance, and user-friendliness, these heating systems make a strong case for modern heating technology.

One of the standout features of both the SH15 and SH20 is their energy efficiency. These models utilize state-of-the-art heat pump technology, which allows them to extract heat from the environment even in colder temperatures. This results in significantly lower energy consumption compared to traditional heating systems, leading to reduced utility bills and a lower carbon footprint. The SH15 is designed for smaller spaces, while the SH20 offers a bit more power, making it suitable for larger areas or homes with greater heating demands.

Both models incorporate advanced inverter technology, which adjusts the compressor speed depending on the heating requirements. This ensures that the units operate at optimal efficiency, providing consistent temperature control while minimizing energy waste. Inverter-driven systems contribute to quieter operation as well, which is ideal for residential settings where noise can be a concern.

User-friendliness is another hallmark of the Friedrich SH15 and SH20. Equipped with intuitive digital controls, users can easily set their preferred temperatures and schedules, allowing for personalized comfort. Moreover, both models support smart home integration, enabling remote access and control through mobile applications. This feature not only enhances convenience but also allows users to monitor energy usage and make adjustments on the fly.

Durability is a key characteristic of these heating systems. Constructed with high-quality materials, the SH15 and SH20 are designed to withstand harsh environmental conditions, ensuring long-lasting performance. They also feature advanced air filtration systems that improve indoor air quality by effectively removing allergens and other pollutants.

In summary, the Friedrich SH15 and SH20 embody the cutting-edge of heating technology, offering powerful, efficient, and user-friendly solutions for diverse heating needs. With their advanced features, smart technology integration, and robust construction, these models are well-suited for modern living, ensuring comfortable and environmentally responsible heating year-round.