Lincoln Electric SVM207-A service manual Printed Circuit Board Removal, Figure F.10 Door Removal

Page 82

Section TOC

Master TOC

F-44	TROUBLESHOOTING AND REPAIR	F-44

PRINTED CIRCUIT BOARD REMOVAL

AND REPLACEMENT PROCEDURE (continued)

FIGURE F.10 – DOOR REMOVAL

Return to

Return to Section TOC

Return to

Return to Master TOC

4 Pin Plug

PROCEDURE

4 Self Tapping Screws (at corners)

12 Pin Plug

1/4" Q.C. Tabs

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Before starting the following procedure, refer to the topic “PC Board Troubleshooting Procedures” at the beginning of this section.

1.Remove the engine spark plug wires.

2.With a 5/16” nut driver or socket, remove the 6 sheet metal screws from the case top.

3.Remove the rubber gasket (cover seal) from the lift bail.

4.Remove the fuel cap. The rubber gasket for the fill tube will come off with the case top.

5.Remove the case top, then reinstall the fuel cap.

6.With the 5/16” nut driver, remove the 5 screws holding the right case side.

7.Remove the right case side by lifting up and out.

8.Remove the 12-pin and 4 pin molex plugs from the Printed circuit board.

9.Remove leads 7 and 9 from two 1/4” Q.C. connec- tors from the board.

10.With a 1/4” phillips head screw driver, remove four self tapping screws holding the printed circuit board to the panel.

CAUTION

Be sure to follow the recommended static-free meth- ods for handling printed circuit boards. Failure to do so can result in permanent damage to the equipment.

11.Replace the old printed circuit board with a new one.

12.Replace 4 self tapping screws previously removed.

13.Connect the two Molex plugs and the 7 and 9 leads to P.C. Board.

14.Replace any cable ties that were cut during the removal procedure.

15.Reinstall the case side, fuel cap, lift bail gasket, case top, and spark plug wires.

RANGER® 3 PHASE

Image 82

Contents Ranger 3 Phase Safety Ranger 3 PhaseFumes and Gases Welding Cutting Précautions DE Sûreté Safety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Auxiliary Power InstallationTechnical Specifications Ranger 3 Phase K2337-1 & K2337-2 Height Width Depth WeightSpark Arrester Safety PrecautionsMachine Grounding TowingVehicle Mounting PRE-OPERATION ServiceGasoline Can cause fire or explosionHigh Altitude Operation Welding Output CablesTotal Combined Length of Electrode and Work Cables Angle of OperationInstructions Gfci Duplex Receptacles Auxiliary PowerVolt 3 Phase Receptacle with Ground 120/240 Volt Dual Voltage ReceptacleAuxiliary Power While Welding Ground WireStandby Power Connections TABLE A.1 Simultaneous Welding and PowerConnection of Ranger 3 Phase to Premises Wiring Figure A.3USE These Devices with a Ranger 3 Phase Electrical Device USE with the Ranger 3 PhaseDevices Without Addi Tional Resistive Type Loads Table of Contents Operation Section GENERAL DESCRIPTION Engine SwitchOperation Welder Controls Function and OperationRange Switch Polarity SwitchRanger 3 Phase Approximate Fuel Consumption Control DialStick Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process TIG Constant Current WeldingStick Auto Starting the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Stopping the EngineTable of Contents Accessories Section Accessories K1745-1 Welding GAS Cylinder LPG Tank HolderStick WIRE FEEDRECOMMENDED EQUIPMENT TIGRanger 3 Phase Table of Contents Maintenance Section Maintenance Safety PrecautionsOIL Filter Change Gfci Receptacle Testing and RESET- Ting ProcedureAIR Cleaner and Other Maintenance Slip Rings Do not attempt to polish slip rings while engine is runningFram CA79 BatteryEngine Maintenance Parts KOHLER C23S CHAMPION RC12YCMAINTENANCED-5 Figure D.1 Major Component LocationRanger 3 Phase 1TABLE of CONTENTS-THEORY of Operation Section E-1 General Description Theory of OperationEngine Components and Operation ROTOR, Stator & Control Circuits Figure E.2 ROTOR, Stator and Control CircuitsWeld Circuitry Figure E.2 Weld Circuitry1TABLE of Contents Troubleshooting and Repair F-1 Troubleshooting and Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Return to SectionDiagram Perform the Output Bridge Test Gram Wiring Wiring Diagram Troubleshooting and Repair Figure F.4 and/or the Wiring Test Description Rotor Voltage Test ProcedureMaterials Needed Test Procedure Rotor Voltage TestRotor Resistance Test TEST PROCEDURE Figure F.2 Slip RingsAuxiliary and Field Winding Test Auxiliary Windings To test the 480 VAC 3 Phase windingProbes Reading To test the 120 VAC windingFigure F.4 Control PC Board Field WindingRanger 3 Phase Output Rectifier Bridge Test Figure F.5 OUTPUT RECTIFIER + Meter Lead Meter ReadingToroid Test Toroid Test Charging Circuit Test Voltage Regulator AC Lead DC Lead Engine Throttle Adjustment Test Engine Throttle Adjustment Test Low Idle Adjustment SolenoidNut Housing Figure F.9 115VAC Supply Waveform High IDLE- no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Scope SettingsHigh Idle no Load Output Control AT Maximum Typical DC Weld Output Waveform CV Mode Machine LoadedTypical DC Weld Output Waveform CC Mode Machine Loaded to 200 Amps AT 26 VDCTypical AC Weld Output Waveform Machine Loaded to 225 Amps AT 25 VDCAbnormal Open Circuit Weld Voltage Waveform CV Mode Abnormal Open Circuit DC Weld Voltage Waveform Normal Open Circuit Weld Voltage Waveform CV Mode Normal Open Circuit DC Weld Voltage Waveform CC Mode Normal Open Circuit AC Weld Voltage Waveform Ranger 3 Phase Brush Removal and Replacement Procedure Brush Removal and Replacement Procedure ProcedureBrush Assembly Bracket Bolts Ranger 3 Phase Printed Circuit Board Removal Replacement Procedure Printed Circuit Board Removal Figure F.10 Door RemovalOutput Rectifier Bridge Removal Replacement Procedure Output Rectifier Bridge Removal Figure F.11 OUTPUT RECTIFIERENGINE/ROTOR Removal and Replacement Procedure ENGINE/ROTOR Removal and Replacement Procedure Procedure Rotor Removal Procedure Figure F.13 Engine and Rotor Removed from StatorReassembly Procedure Retest After Repair Table of Contents Diagram Section Ranger 3-PHASE RaNGEr 3 phaSESchEmaTic cOmplETE machiNE l12259 L12259ElEcTrical DiaGramS