Lincoln Electric SVM128-A Connection of Lincoln Electric Wire Feeders, Connection of the LN-7 to

Page 30

TOC

TOC

C-4

C-4

ACCESSORIES

CONNECTION OF LINCOLN ELECTRIC WIRE FEEDERS

Return to Section

Return to Section TOC

Return to Master

Return to Master TOC

CONNECTION OF THE LN-7 TO THE

SA-250 WITH K623-1 WIRE FEED MODULE USING K867 UNIVERSAL ADAPTER (SEE FIGURE C.1.)

1.Shut the welder off.

2.Connect the electrode cable from the LN-7 to the “+” terminal of the welder. Connect the work cable to the “CV–” terminal of the welder.

NOTE: Welding cable must be sized for current and duty cycle of application.

NOTE: Figure C.1 shows the electrode connected for positive polarity. To change polarity, shut the welder off and reverse the electrode and work cables at the SA-250 output terminals.

3.Connect the K867 Universal Adapter to the K291 or K404 input cable and the 14 pin amphenol of the SA-250 as indicated in Figure C.1. Make the prop- er connections for local or remote control accord- ing to Figure C.1.

4.Connect the K291 or K404 input cable to the LN-7.

5.Place the IDLER switch in the “HIGH” position.

CAUTION

Any increase of the high idle engine RPM by changing the governor setting or overriding the throttle linkage will cause an increase in the AC auxiliary voltage. If this voltage goes over 140 volts, wire feeder control circuits may be damaged. The engine governor set- ting is preset at the factory — do not adjust above RPM specifications listed in this manual.

6. Adjust wire feed speed at the LN-7.

NOTE: For remote control, a K775 remote control is required. See Figure C.1.

CAUTION

When the welder is in local control, the electrode is always “HOT.”

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

FIGURE C.1

SA-250/LN-7 WITH K867 ADAPTER CONNECTION DIAGRAM

 

 

SPARE

Insulate Each

 

 

14 PIN

82

LN-7

 

81

Unused Lead

 

AMPHENOL

CONTROL

 

 

42

Individually

BOX

 

 

41

 

 

+

 

31

31

 

 

32

32

 

CV-

 

2

2

 

 

4

4

K291 OR K404

 

 

21

21

TO

 

GND

GND

INPUT CABLE

K867 UNIVERSAL

 

GREEN

 

WORK

 

 

ADAPTER PLUG

75

75

 

 

 

ELECTRODE CABLE

76

76

 

77

77

K775 OPTIONAL

TO LN-7

 

Splice Leads

 

 

REMOTE CONTROL

and Insulate

SA-250

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SHIELD-ARCTMSA-250 Safety SA-250Electric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications SA-250Safety Precautions Location and VentilationStoring PRE-OPERATION Engine Service Exhaust Spark Arrester Cooling SystemMuffler TrailerElectrical Output Connections Welding Cable ConnectionsAuxiliary Power RECEPTACLES, PLUGS, and HAND-HELD Equipment Machine GroundingCircuit Breakers SA-250 Table of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features WelderWelding Capability LimitationsControls and Settings WELDER/GENERATOR ControlsControl of Welding Current Current Range SelectorDiesel Engine Controls Figure B.3 Diesel Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine Check and fill the engine fuel tankStopping the Engine Cold Weather StartingBREAK-IN Period Welding Operation After you finish weldingTable B.1 Range Settings for Wire SIZE/SPEED Auxiliary Power 12B-12Table of Contents Accessories OPTIONS/ACCESSORIES TIG Welding Accessories Semiautomatic Welding AccessoriesConnection of Lincoln Electric Wire Feeders Connection of the LN-7 toPIN Amphenol Connection of the LN-25 to Unused Lead IndividuallyFigure C.4 SA-250/LN-25 Across the ARC Connection Diagram Control K487-25 Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.1 OIL Drain and Refill Eliminate Air from the Fuel System HOW to Eliminate AIR from the Fuel System Self-vent method Figure D.4 Eliminating AIR from the Fuel SystemFigure D.5 Engine Coolant Drain Plug Figure D.6 Tightening the FAN Belt First 25-50 Hours Daily or BeforeStarting Engine EveryBattery Maintenance Cleaning the BatteryWELDER/GENERATOR Maintenance Idler Maintenance Figure D.5 Major Component Locations SA-250 Table of Contents Theory of Operation Section Theory of Operation ALTERNATOR, and ProtectionCircuits Excitation Flashing Auxiliary and Field Feedback CoilsInterpole and Series Coils Fine Current Adjustment Current Range SelectorEngine Idler Circuit DC Generator Machines Mechanical CouplingSA-250 Table of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures PC Board can be damaged by static electricityTroubleshooting Guide Observe Safety GuidelinesDetailed in the beginning of this manual Shunt Field Winding Test Field Shunt Winding Test Output Problems Function Problems Function Problems Troubleshooting & Repair Problems Possible Areas Symptoms Misadjustments Course of ActionWelding Problems Alternator Rotor Test Test DescriptionMaterials Needed Test Procedure Slip Rings BrushesFigure F.2 Measuring Rotor Resistance Figure F.3 Measuring Rotor Resistance to Ground Field Shunt Winding Test Field Shunt Winding Test PIN TAB Idler Solenoid Test Idler Solenoid Test Engine Throttle Adjustment Test Engine Throttle Adjustment Test Strobe Tach MethodFrequency Counter Method Oscilloscope MethodAdjusting Screw Locking NUT Flashing the Fields DescriptionProcedure Do not remove brush holderScope Settings Normal Open Circuit Voltage Waveform 115VAC SupplyHigh Idle no Load Fine Current Control Rheostat AT Maximum Normal Open Circuit DC Weld Voltage Waveform Machine Loaded Selector Switch AT Maximum Position Typical DC Weld Output Voltage WaveformAlternator Rotor Removal Replacement Replacement Alternator Rotor RemovalLoosen Screws Alternator Cover Slip Rings Brushes Figure F.13 Rotor Removal Replacement Alternator Stator Removal and Replacement Procedure Alternator Stator RemovalField Bridge Rectifier VAC Receptacle Circuit Breaker Genernator Brush HOLDER/COIL Cables Figure F.18 Drill Spot Locations Generator Frame Removal and Replacement Generator Frame Removal See Figure F.19 for steps 4Figure F.20 Wire and Selector Switch Connections Figure F.21 Case Front Removal Rope Sling ENGINE/GENERATOR Mounting Holes Troubleshooting & Repair Generator Armature Removal and Replacement Generator Armature Removal Figure F.23 Blower Paddle RemovalEngine Output AC Auxiliary Power Receptacle OutputRetest After Repair Welder DC OutputSA-250 Electrical Diagrams Section Section G SA-250 Electrical Diagrams Wiring DiagramWire Feed Module Wiring Diagram Idler PC Board M13708 Schematic Idler PC Board M13708 Components SVM Error Reporting Form

SVM128-A specifications

The Lincoln Electric SVM128-A is a cutting-edge welding machine designed to meet the demands of both professional welders and DIY enthusiasts. This versatile welding power source brings together advanced technology and robust design, making it a reliable choice for various welding applications.

One of the standout features of the SVM128-A is its capability to perform multiple welding processes. It supports MIG, TIG, and stick welding, allowing users to tackle a wide range of projects with ease. This multi-functionality makes it ideal for professionals working in different industries, as well as for hobbyists who enjoy diverse welding tasks.

The SVM128-A is equipped with inverter technology, which enhances its performance by providing a more stable arc and improved energy efficiency. This technological advancement contributes to lower operational costs and allows for a more consistent weld quality across different materials and thicknesses. Additionally, the inverter technology enables the machine to be lightweight and portable, making it convenient for jobs that require mobility.

Another prominent characteristic of the SVM128-A is its user-friendly interface. The machine features intuitive controls and a digital display that allows operators to easily set the desired welding parameters. This simplified setup helps reduce the learning curve for new users while also offering precise control for experienced professionals.

The Lincoln Electric SVM128-A is designed with durability in mind. Its robust construction ensures that it can withstand the rigors of frequent use in demanding environments. The machine is also equipped with various safety features, including thermal overload protection and a duty cycle rating that prevents overheating, ultimately extending its lifespan.

For optimal performance, the SVM128-A provides adjustable output options, allowing users to customize the welding parameters based on their specific needs. This flexibility makes it suitable for welding various metals, including steel, aluminum, and stainless steel.

In summary, the Lincoln Electric SVM128-A combines versatility, advanced technology, and a user-friendly design. With its capability to perform multiple welding processes, lightweight construction, and durable features, it stands out as an excellent option for anyone looking to achieve high-quality welds. Whether for professional or personal use, the SVM128-A is poised to deliver reliable performance and exceptional results.
Top Page Image Contents