Lincoln Electric SVM128-A service manual Figure F.21 Case Front Removal

Page 98

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-44

F-44

TROUBLESHOOTING & REPAIR

GENERATOR FRAME REMOVAL

AND REPLACEMENT (continued)

FIGURE F.21 – CASE FRONT REMOVAL

STEP #19

STEP #18

STEP #17

See Figure F.21 for steps 17 - 19.

17.With the 9/16" wrench, remove the four bolts and lock washers holding the case front to the welder frame. There are two bolts on each side.

18.With the 1/2" wrench, remove the two bolts and nuts and washers from the gas tank rails - one on each side.

19.Carefully clear all remaining leads and lift up and set the front panel assembly to the left side of the machine. Make sure all leads are clear.

SA-250

Image 98

Contents SHIELD-ARCTMSA-250 Safety SA-250Electric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications SA-250Storing Safety PrecautionsLocation and Ventilation PRE-OPERATION Engine Service Exhaust Spark Arrester Cooling SystemMuffler TrailerElectrical Output Connections Welding Cable ConnectionsCircuit Breakers Auxiliary Power RECEPTACLES, PLUGS, and HAND-HELD EquipmentMachine Grounding SA-250 Table of Contents Operation Section Operating Instructions Safety InstructionsOperation General DescriptionRecommended Applications Operational Features and ControlsDesign Features WelderWelding Capability LimitationsControls and Settings WELDER/GENERATOR ControlsControl of Welding Current Current Range SelectorDiesel Engine Controls Figure B.3 Diesel Engine ControlsStarting the Engine Engine OperationBefore Starting the Engine Check and fill the engine fuel tankBREAK-IN Period Stopping the EngineCold Weather Starting Welding Operation After you finish weldingTable B.1 Range Settings for Wire SIZE/SPEED Auxiliary Power 12B-12Table of Contents Accessories OPTIONS/ACCESSORIES TIG Welding Accessories Semiautomatic Welding AccessoriesConnection of Lincoln Electric Wire Feeders Connection of the LN-7 toPIN Amphenol Connection of the LN-25 to Unused Lead IndividuallyFigure C.4 SA-250/LN-25 Across the ARC Connection Diagram Control K487-25 Table of Contents Maintenance Routine and Periodic Maintenance Engine MaintenanceFigure D.1 OIL Drain and Refill Eliminate Air from the Fuel System HOW to Eliminate AIR from the Fuel System Self-vent method Figure D.4 Eliminating AIR from the Fuel SystemFigure D.5 Engine Coolant Drain Plug Figure D.6 Tightening the FAN Belt First 25-50 Hours Daily or BeforeStarting Engine EveryBattery Maintenance Cleaning the BatteryWELDER/GENERATOR Maintenance Idler Maintenance Figure D.5 Major Component Locations SA-250 Table of Contents Theory of Operation Section Circuits Theory of OperationALTERNATOR, and Protection Excitation Flashing Auxiliary and Field Feedback CoilsEngine Idler Circuit Interpole and Series Coils Fine Current AdjustmentCurrent Range Selector DC Generator Machines Mechanical CouplingSA-250 Table of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures PC Board can be damaged by static electricityDetailed in the beginning of this manual Troubleshooting GuideObserve Safety Guidelines Shunt Field Winding Test Field Shunt Winding Test Output Problems Function Problems Function Problems Troubleshooting & Repair Problems Possible Areas Symptoms Misadjustments Course of ActionWelding Problems Materials Needed Alternator Rotor TestTest Description Test Procedure Slip Rings BrushesFigure F.2 Measuring Rotor Resistance Figure F.3 Measuring Rotor Resistance to Ground Field Shunt Winding Test Field Shunt Winding Test PIN TAB Idler Solenoid Test Idler Solenoid Test Engine Throttle Adjustment Test Engine Throttle Adjustment Test Strobe Tach MethodFrequency Counter Method Oscilloscope MethodAdjusting Screw Locking NUT Flashing the Fields DescriptionProcedure Do not remove brush holderHigh Idle no Load Fine Current Control Rheostat AT Maximum Scope SettingsNormal Open Circuit Voltage Waveform 115VAC Supply Normal Open Circuit DC Weld Voltage Waveform Machine Loaded Selector Switch AT Maximum Position Typical DC Weld Output Voltage WaveformAlternator Rotor Removal Replacement Replacement Alternator Rotor RemovalLoosen Screws Alternator Cover Slip Rings Brushes Figure F.13 Rotor Removal Replacement Alternator Stator Removal and Replacement Procedure Alternator Stator RemovalField Bridge Rectifier VAC Receptacle Circuit Breaker Genernator Brush HOLDER/COIL Cables Figure F.18 Drill Spot Locations Generator Frame Removal and Replacement Generator Frame Removal See Figure F.19 for steps 4Figure F.20 Wire and Selector Switch Connections Figure F.21 Case Front Removal Rope Sling ENGINE/GENERATOR Mounting Holes Troubleshooting & Repair Generator Armature Removal and Replacement Generator Armature Removal Figure F.23 Blower Paddle RemovalEngine Output AC Auxiliary Power Receptacle OutputRetest After Repair Welder DC OutputSA-250 Electrical Diagrams Section Section G SA-250 Electrical Diagrams Wiring DiagramWire Feed Module Wiring Diagram Idler PC Board M13708 Schematic Idler PC Board M13708 Components SVM Error Reporting Form