Lincoln Electric SVM104-A service manual Figure F.11-Power Board Test Points

Page 69

Section TOC

Master TOC

TROUBLESHOOTING & REPAIR

F-28

POWER BOARD TEST

Return to

Return to Section TOC

Section TOC

Return to

Return to Master TOC

to Master TOC

H1

LEAD

H2

LEAD

C

LEADS

NEG

LEAD

#40

LEADS

MOUNTING1J21 SCREWS

			J21
H1		40 G1
		B	G2
			G2
H2	4J20
	4J20
	2J20	J20	1J20
	2J20		1J20

C

NEG

#40

3J22 J22 1J22

4J222J22

POWER BOARD

L7941

Return to

Return

FIGURE F.11-Power Board Test Points

Return to Section TOC

Return to Master TOC

TEST PROCEDURE

1. Connect input power to machine.

2.Turn ON/OFF Power Switch to OFF.

Test A: Test for 12 VAC voltage to Power Board

1.Locate and insert probes into Power Board Plug locations 1J22 (lead H4) and 3J22 (lead H3). See Figure F.11. Carefully insert the probes into

the lead cavity to make contact with the lead.

2.Turn ON/OFF Power Switch to ON.

a.If 12 VAC is NOT present, check Plug J22 for loose or faulty wiring.

bIf no loose or faulty wiring is

found, perform Main Transformer Test.

3.Turn ON/OFF Power Switch to OFF.

PRO-CUT 60

Image 69

Contents SVM104-A Electric Shock can kill SafetyWelding or Cutting Sparks can cause fire or explosion Electric and Magnetic Fields IiiSûreté Pour Soudage a L’Arc Précautions DE SûretéMaster Table of Contents for ALL Sections Table of Contents Technical Specifications PRO-CUT InstallationSelect Proper Location Safety Precautions Electric Shock can KillHigh Frequency Interference Protection TiltingInput Electrical Connections ➁ ➂ ➀ ➃Fuse and Wire Sizes Input Power Supply ConnectionsGround Connection AIR Input Connections 208/230/460 VAC machines Reconnect ProcedureWork Output ConnectionsOperation Section Table of ContentsElectric Shock can kill OperationDesign Features Advantages Operational Features and ControlsGeneral Description Recommended Processes and EquipmentControls and Settings Cutting and Gouging CapabilityLimitations ON/OFF Operating StepsUse Pilot Arc Properly Cutting Procedure RecommendationsCutting Thin Gauge Sheet Metal Cutting Expanded Metal Figure B.3 -- Gouging Metal Return to Section TOC Accessories Section OPTIONS/ACCESSORIES AccessoriesSection D Maintenance SectionSafety Precautions MaintenanceCapacitor Discharge Procedure Procedure DescriptionFigure D.1 Capacitor Discharge Procedure ProcedurePerform the following daily Routine and Periodic MaintenanceMaintenance PRO-CUT Theory of Operation Section Theory of Operation SectionInput Line Voltage and Main Transformer Theory of OperationFigure E.3 Output Rectification, Control and Feedback Output Rectification Control and FeedbackHigh Voltage / High Pilot ARC Theory of OperationFigure E.7 Transistor Switching Operation Transistor Switching OperationThermal Protection Pulse Width ModulationThermostat Thermal SensorPRO-CUT Troubleshooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & RepairBoard can be dam- aged by static electricity Troubleshooting PC Board Troubleshooting ProceduresTroubleshooting Guide PRO-CUT Troubleshooting GuideConnect ALL Input Disconnect ALL Input Machine Troubleshooting & Repair Function Problems AIR Flow Problems Cutting Problems Power Board Connector Location Control Board Connector LocationCapacitor Discharge Procedure Insulated Pliers Gloves Figure F.19-Capacitor Discharge ProcedureTest Description Work Torch and Cable Resistance Test ProcedureFigure F.4 Torch and Cable Resistance Test Points Internal Trigger Safety Circuit TestReturn to Return to Section TOC Figure F.6-Control Board and 4-pin Locations Test Description Transistor Module TestTest Procedure J21 Main Transformer Test Test a Main Secondary Voltage Test Test ProcedureCR2 Power Board Test Figure F.11-Power Board Test Points Transistor Module Test Troubleshooting & Repair High Voltage Transformer and Circuit Test Figure F.12-High Voltage Test Component Locations Test C Test Resistance of High Voltage Transformer Secondary REMOVAL/REPLACEMENT Description ON/OFF Power Switch Removal➂ ➃ ➄ REMOVAL/REPLACEMENT ProcedureControl Board Removal To Section TOC Power Board Removal Figure F.14-Power Board Removal/Replacement Return to Return to Section TOC Transistor Module Removal 41TROUBLESHOOTING & RepairRemoval Procedure SCR Module Removal Socket Head CAP Screws Torque to Power Board REMOVAL/ Replacement Procedure FAN Blade and FAN Motor REMOVAL/REPLACEMENT Figure F.17-Fan Blade & Fan Motor To Section TOC Torch Head REMOVAL/REPLACEMENT Figure F.18-Torch Head Removal/Replacement Section TOC Retest After Repair Maximum Acceptable Output Voltage AT Minimum Output SettingInput Idle Amps Recommended Meters for Machine Output TestsPRO-CUT Electrical Diagrams Electrical DiagramsStatus Board Schematic Diagram H E M a T I C Bypass Board Schematic Diagram M15603Bypass Board Schematic Diagram M17322 PRO-CUT Electrical Diagrams Identification Control BoardPower Board Identification Power BoardM15601 Status Status PC BoardM15601 Status PC BoardBypass Bypass PC Board M15603Bypass PC Board M15603 Bypass PC Board M17322 Bypass PC Board M17322 0 , J 2 Wiring Diagram for Codes 10112Wiring Diagram for Codes 9819 Control Board Schematic Drawing G2015 Power Board Schematic Design SVM Error Reporting Form