Lincoln Electric SVM104-A service manual ➂ ➃ ➄, REMOVAL/REPLACEMENT Procedure

Page 76

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-35	TROUBLESHOOTING & REPAIR

ON/OFF POWER SWITCH REMOVAL

(LATER CODES MAY HAVE TOGGLE SWITCH)

➂ ➃ ➄

➁

➅

0

1

➀	➆

➀ON/OFF POWER SWITCH KNOB

➁ SCREW (SECURING KNOB)

➂ FACE PLATE

➃SCREWS (SECURING FACE PLATE)

➄ SWITCH

➅ L1 & L2 LEADS

➆ T1 & T2 LEADS

FIGURE F.13-ON/OFF Power Switch Removal/Replacement

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

REMOVAL/REPLACEMENT PROCEDURE

1.Disconnect input power to the machine.

2.Perform the CAPACITOR DISCHARGE PROCEDURE.

3.Remove the Right Case Side Assembly by removing the sheet metal screws.

4.Remove the black ON/OFF Power Switch knob and plastic insert by unscrewing the small screw in the center of the knob. Remove from the shaft. See Figure F.13.

5.Remove the face plate by squeezing the two tabs together and sliding the plate off. See Figure F.13.

6.Loosen the four screws on the plastic frame. These screws go through the Case Front Assembly into the line switch. When the screws no longer engage the line switch, remove the line switch so it can be worked on.

7.Remove and save the electrical tape. The electrical tape will be re-applied during assembly.

8.Remove leads T1, T2, L1, & L2.

9.Install new ON/OFF Power Switch in reverse order of removal. Be sure to re-apply electrical tape to switch.

PRO-CUT 60

Image 76

Contents SVM104-A Safety Electric Shock can killWelding or Cutting Sparks can cause fire or explosion Iii Electric and Magnetic FieldsPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Technical Specifications PRO-CUTSafety Precautions Electric Shock can Kill Select Proper LocationHigh Frequency Interference Protection Tilting➁ ➂ ➀ ➃ Input Electrical ConnectionsInput Power Supply Connections Fuse and Wire SizesGround Connection AIR Input Connections Reconnect Procedure 208/230/460 VAC machinesOutput Connections WorkTable of Contents Operation SectionOperation Electric Shock can killOperational Features and Controls Design Features AdvantagesGeneral Description Recommended Processes and EquipmentCutting and Gouging Capability Controls and SettingsLimitations Operating Steps ON/OFFCutting Procedure Recommendations Use Pilot Arc ProperlyCutting Thin Gauge Sheet Metal Cutting Expanded Metal Figure B.3 -- Gouging Metal Return to Section TOC Accessories Section Accessories OPTIONS/ACCESSORIESMaintenance Section Section DMaintenance Safety PrecautionsCapacitor Discharge Procedure Procedure DescriptionProcedure Figure D.1 Capacitor Discharge ProcedureRoutine and Periodic Maintenance Perform the following dailyMaintenance PRO-CUT Theory of Operation Section Theory of Operation SectionTheory of Operation Input Line Voltage and Main TransformerOutput Rectification Control and Feedback Figure E.3 Output Rectification, Control and FeedbackHigh Voltage / High Theory of Operation Pilot ARCTransistor Switching Operation Figure E.7 Transistor Switching OperationPulse Width Modulation Thermal ProtectionThermostat Thermal SensorPRO-CUT Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuideTroubleshooting PC Board Troubleshooting Procedures Board can be dam- aged by static electricityTroubleshooting Guide Troubleshooting Guide PRO-CUTConnect ALL Input Disconnect ALL Input Machine Troubleshooting & Repair Function Problems AIR Flow Problems Cutting Problems Control Board Connector Location Power Board Connector LocationCapacitor Discharge Procedure Figure F.19-Capacitor Discharge Procedure Insulated Pliers GlovesTest Description Torch and Cable Resistance Test Procedure WorkFigure F.4 Torch and Cable Resistance Test Points Safety Circuit Test Internal TriggerReturn to Return to Section TOC Figure F.6-Control Board and 4-pin Locations Transistor Module Test Test DescriptionTest Procedure J21 Main Transformer Test Test Procedure Test a Main Secondary Voltage TestCR2 Power Board Test Figure F.11-Power Board Test Points Transistor Module Test Troubleshooting & Repair High Voltage Transformer and Circuit Test Figure F.12-High Voltage Test Component Locations Test C Test Resistance of High Voltage Transformer Secondary ON/OFF Power Switch Removal REMOVAL/REPLACEMENT DescriptionREMOVAL/REPLACEMENT Procedure ➂ ➃ ➄Control Board Removal To Section TOC Power Board Removal Figure F.14-Power Board Removal/Replacement Return to Return to Section TOC 41TROUBLESHOOTING & Repair Transistor Module RemovalRemoval Procedure SCR Module Removal Socket Head CAP Screws Torque to Power Board REMOVAL/ Replacement Procedure FAN Blade and FAN Motor REMOVAL/REPLACEMENT Figure F.17-Fan Blade & Fan Motor To Section TOC Torch Head REMOVAL/REPLACEMENT Figure F.18-Torch Head Removal/Replacement Section TOC Maximum Acceptable Output Voltage AT Minimum Output Setting Retest After RepairInput Idle Amps Recommended Meters for Machine Output TestsPRO-CUT Electrical Diagrams Electrical DiagramsStatus Board Schematic Diagram Bypass Board Schematic Diagram M15603 H E M a T I CBypass Board Schematic Diagram M17322 PRO-CUT Electrical Diagrams Control Board IdentificationPower Board Power Board IdentificationStatus PC Board M15601 StatusStatus PC Board M15601Bypass PC Board M15603 BypassBypass PC Board M15603 Bypass PC Board M17322 Bypass PC Board M17322 Wiring Diagram for Codes 10112 0 , J 2Wiring Diagram for Codes 9819 Control Board Schematic Drawing G2015 Power Board Schematic Design SVM Error Reporting Form