Lincoln Electric IM544-B manual Commander 400 Stick & Wire / LN-23P Connection Diagram

Page 36

COMMANDER 400 STICK & WIRE / LN-23P CONNECTION DIAGRAM

WARNING

 

Do not operate with panels open.

Keep guards in place.

Disconnect NEGATIVE (-) BATTERY LEAD

Keep away from moving parts.

before servicing.

Only qualified personnel should install,use

Do not touch electrically live parts.

or service this equipment.

CONNECTION

F-4

DIAGRAM:

 

14PIN

AMPHENOL

ADAPTER

KIT

K350-1

6 PIN

LN-23P

WIRE FEEDER

TO WORK

ELECTRODE

AMPHENOL

COMMANDER 400

ELECTRODE CABLE

TO WORK

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL/REMOTE SWITCH IN "REMOTE" POSITION.

N.D. ON COMMANDER 400 STICK & WIRE, THE OUTPUT CONTROL SWITCH MUST BE IN THE "WELDING

TERMINALS REMOTELY CONTROLLED" POSITION.

12-13-96

S22911

DIAGRAMS

F-4

Image 36
Contents Commander Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Installation Welding Range Open Circuit Voltage Auxiliary Power1HEIGHT2 Width Depth Weight Bore x StrokeSafety Precautions LOCATION/VENTILATIONStacking Angle of OperationPRE-OPERATION Engine Service High Altitude OperationTowing OILEngine Cooling System Battery Connection Electrical Output ConnectionsFuel CAP Muffler Outlet PipeAuxiliary Power Receptacles Standby Power ConnectionsWelding Output Cables Machine GroundingPower Safety Instructions OperationOperating Instructions General DescriptionAdditional Design Features For Auxiliary PowerOther Features For Wire WeldingControls and Settings RUN- Stop SwitchStart Pushbutton Engine Temperature Gauge and Light Idler SwitchEngine Alternator Ammeter and Light Idler Operational exceptionsAuxiliary Power Controls Wire Feeder Mode Controls Engine OperationStarting the Engine Stopping the EngineWelder Operation Typical Fuel ConsumptionStick Welding TIG WeldingCommander 400 Settings When Using the K799 HI-FREQ Unit Commander 400 Settings When Using the K930-1 TIG ModuleTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Wire Feed Constant Voltage WELD- ING Stick and Wire Model Connection to LN-25Stick and Wire Model Connection to LN-23P Stick and Wire Model Connection to NA-3Auxiliary Power Operation Simultaneous Welding and AUXIL- Iary Power LoadsAccessories Optional Field Installed AccessoriesRecommended Equipment Maintenance Routine and Periodic MaintenanceEngine Maintenance Fuel Filters Fuel PRE-FILTER/WATER Separator ASSEM- BLYWater Separator Element Battery Handling Cooling System Cooling Blower BeltMake Part Number Troubleshooting HOW to USE Troubleshooting GuideSymptoms Possible AreasCourse of Action Function Problems Output Problems Diagrams Commander Diagrams K488 / K487 Spool GUN Connection DiagramDiagram Commander 400 Stick & Wire / LN-23P Connection DiagramAmphenol 14 PIN Commander 400 Stick & Wire / K867 / LN-8 Connection Diagram Electrode Cable To Wire Feed Unit LN-7 Connection Diagram Electrode Cable Commander 400 Stick & Wire / LN-8 Connection Diagram Dimension Print Commander Basic Course $700.00Precaucion Aviso DE Statement of Limited Warranty Warranty Period 1 2Conditions of Warranty Warranty Limitations